similar to: Can not dial more then 23 calls

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

When a call is placed out the Zap interface there is a long pause followed by an error message from the telco that the call can not be placed as dialed. We have a tdm2413e with 11 1FB (POTS) lines. The number being dialed is a working local number, all dialed numbers get the same error. What should we be looking for ? Best regards, Duane Pudenz Network Infrastructure Manager Shasta

Hi All, Just a little over thought. Sorry if someone already asked about this before. Is it possible to put all 16 Ports of E1 in One Asterisk Server ? And if it's not possible is there any suggestion or alternative for me to use more than 320 lines of outgoing calls on One Asterisk Server ? Thanks ZH -------------- next part -------------- An HTML attachment was

Hello, Now that we've had our new Digium TE406P card in production for 4 days we have discovered audio drop problems that happen randomly across all channels. Here's more about our setup: P4-3.2GHz 2GB ram Slackware Linux 10.1 with custom kernel 2.4.29 Asterisk 1.2beta1 Digium TE406P quad T1 card with the following attached: - 2 x RBS D4/AMI 24 channel T1s - 1 x RBS B8ZS/ESF 24 channel

Hey gang, I've been able to use sipp to produce some call volume on our asterisk server. The server has no problems handling 50 simul calls. But then again, no RTP is being done. I tried to use the rtp echo ability of sipp but that doesn't seem to work right. I also setup a fake number in asterisk that when called by sipp, would dial another number via PRI, hoping that some 729

Hi all, I'm having some problems getting TDMoE setup for the 1st time. I have a TE405P installed in the main server with an ethernet cross-connection to the secondary machine. (Yes, I know about IAX2 but I want to use TDMoE to simulate using T1s.) I'm using -HEAD from yesterday. On the main machine /etc/zaptel.conf: loadzone = us defaultzone=us

Has anyone here used T1s with RBS with asterisk? Cary Fitch

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

After working fine for a week or so my new Quad E1 asterisk 1.8 system has started rejecting outbound calls from the Nortel BMC 450 it is connected to. The cli fills up with these: sig_pri.c: Ring requested on unconfigured channel 255/255 span 3 Is this likely to be a 1) config error 2) cable issue (I made them) 3) hardware problem with the Digium card 4) software (lib pri) Any clues?

Hello everyone. I have server with 2E1 PCI card, asterisk 1.4.35, dahdi 2.4.0, libpri 1.4.12-beta2. One PRI trunk looks to PSTN and take a clocksource from telco. Another trunk looks to PBX with DECT system. Some outgoing calls from asterisk to PSTN drops. The last message that exists before hanging up process is: DEBUG[28467] channel.c: Got a FRAME_CONTROL (8) frame on channel DAHDI/... This

So, I've compiled and installed libpri-1.4.11.5, dahdi-linux-complete-2.4.1+2.4.1 and asterisk-1.6.2.17.1, but chan_dahdi is not getting built. If I do a "make menuselect" in asterisk I see it listed with XXX, meaning that dependencies are not met. XXX chan_dahdi Depends on: res_smdi(M), dahdi(E), tonezone(E), pri(E), ss7(E), openr2(E) res_smdi gets built fine, dahdi is

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Are you looking for local or Long distance? What will these T1s primarily be used for(inbound/outbound, domestic, local, long distance, international) How important are per minute rates to you? how many minutes do you expect to use per month? We are in Tampa Florida and have 15 T1s from several different providers so I may be able to refer you to one if it's a match to what you're

We are experiencing a delay when using the MeetMe service. There is a 1/2 second of delay heard by all parties on the conference call. This delay seems to be consistent with all connected parties, meaning that if there are four connections to the conference room (A, B, C, & D) when user 'A' talks users 'B', 'C', & 'D' will all hear the audio with

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

hello, i installed an asterisk as a pri gateway. Everything is okay. /etc/init.d/zaptel starts successfull with wct4xxp module. /etc/init.d/asterisk starts also successfully. I tested my pri cable and it works. But still my span isn't up. I don't see any error. Do you have any idea? What else i should check? Thanks. My card is 4 span Wildcard TE410P

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

Heh guys, I just received a T400 card, I've been using a T100 for a little while, and it works fine when using a raw channelized T1. I'm relocating my asterisk machine, and PRI's will only be available, haven't found any good config info for PRI's, can someone point me to PRI config info, or let me know what changes I need to make in order to bring them up, I imagine,

Hello Everyone, I must deploy an asterisk system that can support at least 500 pstn outbound calls. It's a challenge as it's the first time i'm gonna build such a large system. I want to have your advice on hardware, software and so on . What i have in my plan is a cluster of servers with quad PRI cards. I will appreciate your advice. Thank you all . --

We are in the process of implementing realtime voicemail. I was wanting to "stress-test" the system to see if or when it would fall over. Is it possible to use sipp to create say 250 calls, each of which leaves a message in the voicemail ? My dialplan is currently [default] exten => stress,1,Answer() exten => stress,2(vm),Voicemail(7777|su) exten => stress,3,Hangup()