similar to: Solved: Unable to load module for TE406P

Hi, I'm unable to load wct4xxp module for TE406P card. I've compiled 2.6.13-rc6, got latest CVS (as of today) of zaptel, but when I try to load the module I get this: kobject_register failed for Unified t4xxp/t2xxp driver (-13) [kobject_register+53/73] kobject_register+0x35/0x49 [bus_add_driver+62/153] bus_add_driver+0x3e/0x99 [driver_register+55/58] driver_register+0x37/0x3a

Guys, I'm trying to configure a TE406P with MFC/R2. here goes my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1

Hi, I've installed an TE406p, asterisk1.2 on tyan opteron board. After installation there is no interrupts from TE406p. Is this board stable? Should i change * version to 1.0.9? Regards, Jason __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

I received a TE406P card from Digium yesterday and have done several tests on it and cannot get it working reliably with any Stable release or even CVS v1.0. What are other people that are using the TE406P card using for an Asterisk version? I tried 1.2.0 beta1 and it seemed to function well except for an unrelated issue with the beta release where the manager interface chokes under

Hello, Now that we've had our new Digium TE406P card in production for 4 days we have discovered audio drop problems that happen randomly across all channels. Here's more about our setup: P4-3.2GHz 2GB ram Slackware Linux 10.1 with custom kernel 2.4.29 Asterisk 1.2beta1 Digium TE406P quad T1 card with the following attached: - 2 x RBS D4/AMI 24 channel T1s - 1 x RBS B8ZS/ESF 24 channel

Hi Guys, I need your recommendation which card to buy?The TE411P or TE406P do they have any difference?I check their brochures they are differ only when it comes to PCI slot voltages.Which card best to use?Btw,Il be using supermicro board with 3.3V and 5.5V?Will il be experiencing problem during the implementation later on if i choose the wrong PCI voltage options?Will it depends on

Hi all, I am having problems detecting fax on a client site using the TE406P (card with echo cancellation module) under 1.2 and was wondering if anybody was having or has had similar problems? Currently I can not get the system to detect fax for love nor money, in zapata.conf the relevant entries are set to: faxdetect=outgoing and I have a fax extension in the necessary context. I have taken

Hi, Does anyone know if it's possible to have 1 port of TE406P to provide T1 PRI to other VoIP gateways? I am trying to provide T1 PRI to one of our old Clarent gateways to integrate it to Asterisk. Can anyone help? Thank you. Andy

I just wanted to post here and let everyone know that the TE406P (quadspan T1/E1 with hardware echo can) kicks some serious ass. We've been running a PRI now for over a year with Asterisk (every single call in and out is through two Asterisk boxes, including faxes) and while the software based echo cancellation is more than adequate, we'd get the occassional "edgy" echo and

hello list i have installed 2 diguim card in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi, My configuration is pri----*(te405p)---iaxclient. My * version is 1.0.7 running on tyan dual opteron board. I have several problems. 1) inbound echo For outbound call(iaxclient-->pri), there is almost no echo. But for inbound(pri-->iaxclient), I can hear distinct echo. Can Sangoma a104 or digium te406p help this problem? 2)Today i received te406p. I know T1/E1 jumper. But how can i

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hi. My configuration is Elastix 1.5.2-2 (asterisk 1.4.24, libpri-1.4.3-5, dahdi-2.1.0.4-7 ) and OpenVox d210e connected to telco provider (Euro ISDN). Here is my /etc/dahdi/system.conf: # Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) HDB3/CCS ClockSource span=1,1,0,ccs,hdb3 # termtype: te bchan=1-15,17-31 dchan=16 echocanceller=oslec,1-15,17-31 # Span 2: TE2/0/2 "T2XXP

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC