similar to: Initiating a transfer from an analog handset?

Mine has been working well, but the only problem is that it doesn't support callerid (from the POTS side). > -----Original Message----- > From: John Schmerold [mailto:john@katy.com] > Sent: Tuesday, 5 August 2003 12:37 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] Zhone Zplex 10 units > > Thanks for the Zplex heads up. > > Steven

I've got a Wildcard T100P along with a Zhone Zplex 10 24S/O which has been working fine for me now for a while. These have been pulled out of a working Asterisk installation (as they were no longer required) to use at home only to find that the fan noise is too loud. As such I'm looking to sell off this hardware and replace it with some combination of fanless hardware that will allow me to

Hey guys, I've had a working Asterisk setup going for a while now, but am having problems with the Zhone Zplex 10b thinking that during ringing, an extension has answered the call when infact it hasn't. This only seems to happen on some of the ports and doesn't appear to be specific to the handset. Does anyone have any suggestions as to how I could go about fixing this (aside from

hello all, I still experience the random off-hook on my fxo cxhannels, i am using a zplex-10b channel bank. which does not allow me to call out. The situation still persists...this is what i have in the zapata.conf [channels] context=internal context=incoming context=default usecallerid=no usecallwaiting=no signalling=fxs_ks channel=1-8 signalling=fxo_ks channel=16-24 but i still have the the

This may be a long shot, but I suppose it can't hurt to ask! I have seen chatter regarding Zhone channel banks amongst the asterisk users primarily. In all of my searching I am guessing that the majority of people using the Zhone's are probably reading this, and with the support that I have seen from Zhone so far this is probably my best bet, I recently picked one up for a project

Hi. I was wondering if the zplex in the dev kit could be configured to have all fxs ports, instead of the standard 8 fxo + 16 fxs. If so, anyone managed to do that? Matteo. -- Matteo Brancaleoni Powered by RedHat Linux 8.0 Linux User #153521 -----BEGIN GEEK CODE BLOCK----- Version: 3.12 GS d? s:- a- C+++ UL++++ P+ L+++ E- W+++ N++ o K- w-- O- M-- V-- PS PE- Y PGP++ t 5 X+ R tv- b++ DI D+ G e

hello * users, i am using a zplex 10b(8fxosand 16fxs) connected to a T100 digium card, RH8.0. soon after running * i get this warning "file chan_zap.c,line 4155 (ss_thread):CallewrID returned with error on channel 'zap/7-1' then executes the other applications itself. --executing Wait("Zap/7-1","1") in new stack. -- executing..... it gives the same warning

https://bugs.freedesktop.org/show_bug.cgi?id=74002 Priority: medium Bug ID: 74002 Assignee: nouveau at lists.freedesktop.org Summary: [un]docking Lenovo W530 results in interrupt storm QA Contact: xorg-team at lists.x.org Severity: major Classification: Unclassified OS: Linux (All) Reporter: jcollins at

https://bugs.freedesktop.org/show_bug.cgi?id=74123 Priority: medium Bug ID: 74123 Assignee: nouveau at lists.freedesktop.org Summary: [NVE7] windows maximize behind xfce4-panel until settings viewed QA Contact: xorg-team at lists.x.org Severity: normal Classification: Unclassified OS: Linux (All)

Greetings, I have just purchased several Astra 390 phones ready for asterisk. I have placed a line with adsi=yes in the Zapata.conf file just before channel => 13 I have also added an extension exten => 6199,1,ADSIProg(asterisk.adsi) exten => 6199,2,Hangup in the extensions.conf file. When I try to program the phone I get the following: Asterisk CVS-03/28/04-12:02:10,

I have just make zhone set2default to factory default setting. What do i have to do to make T1 interface zhone match with T100P.

Hi I have the last firmware for zplex, if you like i send it to you, about the second question 24s means 24 extensions so you can configurate as you wish as fxo or fxs. Att Yelson Vivas

HI Asterisk Gurus I'm connecting my * server to a zplex 10B, I'm using a slot on my TE410P card as T1 to connect my server to the channel bank (i use a cross cable), the zplex doesn't show any alarm neither the server. I'm trying to make calls from (ext 1) from the channel bank, to other (ext 2) in the same channel bank, but when I dial the ext number, the dialtone doesn't

I'm having some trouble with placing some iax calls over an openvpn: Setup A is a 1.8GHz Celeron, T100P attached to a Zhone Zplex. Setup B is a 266MHz P2, T100P attached to a Zhone Zplex. Setup C is a 700MHz P3, T100P attached to an Adtran TA 750. Setup D is a 233MHz Pentium, with an X100P. Setups A and B are on the same physical network. IAX calls routed between them work fine. Setup D is

I'm hoping that someone else has seen this problem. Running CVS version from 03/08/03 20:00 T100P -> Zplex-10 All internal call routing seems to work fine. Atempts to make calls on the FXO interface fail. Asterisk picks up the correct number dialed but there seems to be a problem with the Zplex transmitting that number on the POTS line. All attempts to dial out fail with the LEC giving

Hi, I have a mint, like-new (used only once) Zhone Z-Plex channel bank for sale. It has 16 FXS and 8 FXO (part number: Z-PLEX-10-24S/O). It functions as a channel bank, router, and CSU/DSU, combining T1, analog voice, and data. D4, SF, and ESF line formats are supported with AMI or B8ZS coding. It has dual T1 jacks, one ethernet jack, one serial port, one V.35 port, and 24 analog pairs

Modem connect speeds on calls through * seem to be lower than calls made through the telephone company lines or our old Rolm PBX. All data calls have 2 wire analog modems on both ends. For my set up I have channels of a Zhone channel bank tied to 2 modems. The Zhone channel bank interfaces my * server with a T400P card. modem --- Zhone Channel bank - * via T400P card - Zhone channel bank -

I have been playing with Asterisks for about 6 months, and have fallen in love with it. I have finally taken the plunge and gotten a T100P and a Zhone Zplex-10B (24FXS) channel bank. I have read everything that I can find on the mailing list, checked wiki, even searched the web with google. I believe that most everything is configured right The drivers load without error, and asterisks

We were just testing forwarding one of our numbers to a VoIP CLEC and ran into an issue that we've seen before but never figured out the cause of. It seems if you call us and immediately hang up - or if the call is forwarded by Verizon (which stills rings about ? of one time) the Zhone detects the ring and answers the call.. The Zhone however DOESN"T detect that it's no longer

Hi 2 all. I've a nice issue my * system. I have: asterisk latest cvs T100P + Zhone cb (3fxo+10fxs used) Diva Server 4BRI running Capi a bunch of pots and sip phones The whole system is running good (thanks to capigod and Bic. for the help with the Eicon Diva), but there's a very strange issue when calls arrive on the Diva and then bridged to the pots on the channel bank: the voice is not