similar to: txfax on strike while rxfax works flawlessly

Hello folks! I'm trying yo set up a email2fax and fax2email on my asterisk box. The rxfax works fine in my setup. The problem is with the txfax. I have tryed all snadsp version (0.0.2x and 0.0.3x) but I get this errors. Because I can't find anything on Internet I'm hoping u can give me a hand. here are my logs: -- Attempting call on SIP/sip_provider/1234 for application

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

Hi, I noticed a strange behaviour: Faxing using spandsp (TxFax) from my asterisk box to my old, common fax machine at home works fine. Faxing from the same box to my office pc-fax (Hylafax) also worke fine. Receveiving faxes on my asterisk box using spandsp (RxFax) also works fine. It is a PSTN number connected to the digium card of that asterisk box. Then I faxed from my asterisk box (TxFax)

Hi Gang, I'm trying to make an application to upload a tiff via a web interface, slap a cover page onto it, merge the two into a new tiff and send it out via txfax. I'm able to get it out to a fax machine using this sequence: /usr/bin/tiff2pdf /tmp/faxout/1229978819_filea.tif -o /tmp/faxout/1229978819_filea.pdf /usr/bin/gs -dBATCH -dNOPAUSE -q -sDEVICE=pdfwrite

> AFAIK the current recommendation is to use HylaFax with something called iaxmodem. After having been through a lot of problems with RxFax and TxFax I completely agree with this statement. Allthough the initial configuration is a bit complicated, once you have this running you'll get far better reliability. Kind regards, Ardjan Zwartjes.

Hi, I'm using asterisk with a digium TDM400P: I can't send/recive faxes with a Philips fax machine. It seems that the fax machine doesn't recognize the carrier. How can I see the spandsp logs? I've enabled debug on the asterisk CLI, but I can't see any output while the txfax/rxfax application runs. Stefano Arata.

Hi, I'm trying to send a fax from a Zap channel to another Zap channel and I can't - below the logs. How could I solve this? Thanks! In RECEIVER: -- Accepting call from '' to '1980' on channel 0/2, span 1 Urgent handler -- Executing Answer("Zap/2-1", "") in new stack Urgent handler Urgent handler -- Executing Goto("Zap/2-1",

somebody know how to compile the rxfax and txfax apps under asterisk 1.4.0?? i get this errors: Generating embedded module rules ... make[1]: Nothing to be done for `all'. make[1]: Nothing to be done for `all'. make[1]: Nothing to be done for `all'. make[1]: Nothing to be done for `all'. make[1]: Nothing to be done for `all'. [CC] app_rxfax.c -> app_rxfax.o

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, anyone else seen RX/TXFax crashing Asterisk on latest Asterisk SVN? I've now seen it on two machines I tried to set up - one it seems because the tiff file was malformed, but the other is doing: tiff -> tx fax -> zaptel -> pstn -> ddi -> zaptel -> rx fax -> tiff The above crashes every time. If no one else has

Hi Ppl. Once, couple weeks ago when I have updated * from CVS-HEAD something happen and I could not send a fax anymore. After that I have tried previous * CVS versions with different versions of spandsp (0.0.1, 0.0.2pre4, 0.0.2pre10) but without any changes. I have tried that on Fedora Core 2 with libtiff-3.5.7-16.1 and libtiff-devel-3.5.7-16.1. Everything compiles smoothly, but when I try to send

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, We are trying to use astfax (from Inter7) to send faxes directly from email accounts through *. The problem is that the fax machine answer the call when we test astfax (with the line in the README) and then it retries three or four times to send it, and hangup the channel. The fax is connected to a zap channel, and it has an extension configured for itself. This is an excerpt of the

I followed the instructions at http://www.opencall.org/instructions.html and http://lists.digium.com/pipermail/asterisk-users/2003-October/025094.html I was able to compile spandsp (./configure ; make ; make install), "manually" patched asterisk apps/Makefile (/usr/src/asterisk/apps), as the supplied patch does not fit the actual CVS apps/Makefile After make clean ; make install, I

I've been using spandsp and rxfax to receive faxes for a while now and over the past few days I've looked into the other side of things - txfax. I can't seem to get it working properly. I've included debug logs below of both the tx and rx side of things. I've tried three different servers, asterisk v1.0.6, 1.0.9 and CVS, FC2 and FC4, libtiff 3.5.7 and 3.7.1, TE405P and

the attached log with verbose=6 and debug=6 refers. we've got a sangoma A104 (no hwec) with PRI ports 1 & 3 loopbacked to each other. we're trying to have txfax send out on one of those pri ports with rxfax listening on the other side, hence having asterisk send a fax to itself. we however have bad, and i mean really bad (<10%) success rates. we're currently using asterisk

Hi everyone ! I have some aditional info on problem with TXFax and sending multi-page TIFFs. I have made 6 different multi-page TIFFs (Group3 1D with fillbits EOL aligned - 3 pages one TIFF in lowres and one in hires, Group3 2D -3 pages againg in both resolutions , and Group 4 - 3pages in both resolutions), and then tried to send them to Panasonic KX-F1100, Panasonic KX-F500 and SpanDSP

Hi all, I'm using txfax and rxfax to send and receive faxes. I find that txfax performs very well when sending to an old fax machine. However, when trying to send to a Mac (OS X) that accepts faxes, I get a "Trainability test failed" message on the * console (full console log below). I'm OK with being unable to fax to Mac, as I'm just using it to test. For future

Hi, I've compiled rxfax and txfax on my Asterisk box. I've made a small extensions.conf for test so that when I call a number with my Idefisk softphone I activate txfax command. My goal is to try to send a fax using an analog line first and then an ISDN line but I do not know how to specify the channel inside txfax command. Sorry if it may sound a stoopid question but found no docs on

Hi Steve and all, 1. Faxing from asterisk back to the same asterisk (from one Zap channel to another) doesn't work for us. Txfax called with the 'caller' parameter issues CED, while the receiving side needs CNG in order to switch to fax extension with rxfax. 2. This is probably the reason why J2 and our UC don't recognize incoming fax. Thank you. Alex Zarubin Webley Systems

I just want to pdf and email faxes coming in over pstn on a TDM400P. Outgoing faxes would just go out over pstn, not through asterisk. All the voipinfo , etc, howto's are quite complicated. And most use third party apps like Hylafax. I thought there was a rxfax and txfax in 1.4. And 1.6 had app_fax. I'm now using 1.4.22, but I'd go to 1.6 if it made this easier. But I've