similar to: Problem with setting the right dialplan for german PRI E1 on TE405P from digium

Hi, at the moment we have in Avaya Integral PBX with german pri (30 lines). We want to smouthly migrate to an Asterisk server. For this reason: Is it possible to route the external german pri (E1) through Asterisk server to that Avaya PBX? I think at first we need a Digium e1 card 4-Port. But how do we have to configure the routing of the whole PRI? I really would appreciate any sample

Hi, we successfull managed to bridge a PSTN (E1) switch over the TE405P card to our old PBX. So now we could migrate to the * server. But, there are two things we can't live with: 1. A call from the outside to the old PBX is missing a leading 0 before the number. Ex: caller has number 0123456 -> * routes to old pbx -> old pbx sees 123456 as caller number. 2. A call made from a SIP

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet

I am trying to install a TE405P which is to be connected to E1 trunks. I have set the jumpers to E1 (closed), but modprobe wct4xxp still fails with the message: ZT_CHANCONFIG failed for channel 97 - which obviously means the card is still in T1 mode. I have tried everything I can think of, any ideas? TIA

Hello, I would like to know if FreeBSD has drivers for TE405P cards submitted to the ports. I have acquired a card and would really like to use it with FreeBSD. The wiki said the drivers havent been tested yet. Have there been any updates since then? regards Kavit _______________________________________________ Asterisk-Dev mailing list Asterisk-Dev@lists.digium.com

Hello Im from Denmark and i've just got my Digium TE405P. But i have some problems when i connect it to my E1 connection (ISDN30). My telco delivered a alcatel box witch have a G.703 120ohm (DB9 with a serial to rj45) and a 75ohm coax connection. I've tried to connect using the 120ohm with rj45 and a ordinary utp cable. But it dosent seem to work. I've tried several zaptel.conf

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC

Hello all, I really checked voip-info.org but it still seems to be not very easy and I just hope that there is anybody with a simular config. We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper than a channel bank :-) Carrier ----S2M------ * -----S2M------Siemens | |

lspci dont show Digium card. The motherboard is Intel 945gnt. 00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub (rev 02) 00:02.0 Display controller: Intel Corporation 945G Integrated Graphics Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev

Hi, I've got an * box with 4 E1 (TE405P) and a Class 4 Cirpack switch (www.cirpack.com). <IP Network>--<*>--<Cirpack>--<Public PSTN Network> ISDN interco is EuroIsdn, ports are configured ccs, hdb3, crc4. Cirpack is Network, * is Terminal/User. As I encountered some pb with Sip to Zap transcoding (* to Cirpack way poor quality, the other way fine), I tryed to

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hi, one short question: Is it possible for the zaptel driver to deal with multiple phone numbers on one single E1 PRI line? I could make my carrier route +49 xxx aaaaa-zzz and +49 xxx bbbbb-zzz and others down one single PRI trunk to our asterisk box terminating in a Digium TE410P. Does the driver handle this and can I put calls coming in all on the same physical interface put into

Hi, I've been asked to see whether it is possible to do call logging for call center environments at a lower budget than the usual $1000 per channel. Afaik, with PRI this is possible through a high-impendance Y connection, but I wonder whether this would work with the Zapata cards. Anyone ever tried this? Regards, Cees -- XP SP2 can cause cancer in rats

hi, i have the problem that i'm not able to set and receive the Service Indication (SIN) from our E1-PRI and from our ericsson BP250. The problem is, that the Bearer Capability (BC) together with the High Level Compatibility (HLC) and Low Level Compatibility (LLC) forms the Service Indicator (SIN). The SIN is used to determine if the call is voice, fax or data. It's essential to set

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi Everybody, Is there anyone who already uses Asterisk with TE405P card? Is this card going well with the old E400P or T400P drivers? Are there a lot of differences? In the card's data sheet writes this sentece: "Digium has designed the TE405P to be fully compatible with existing software applications..." Is this meaning the the old drivers are also OK for this card? Thank you

Hello, We have finished our tests of the new Digium firmware on the quad T1 cards(TE405P/TE410P). Overall it is a big improvement over the version 1 firmware. Here's the review: http://astguiclient.blogspot.com/2005/09/digium-405p-v2-review.html MATT--- -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Can please someone help me. I have successfully installed Asteriskathome 2.5 on a server with a Intel Server Board SE7525RP2. May issue is after placing the TE405P in the server, it is not booting anymore. Has anyone in here have the same experience? Can someone please point me to the right direction. Thanks in advance, Leonimar __________________________________________________ Do You