similar to: TE110P flashing red/green when PRI connected ... continued

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

Hi, we've installed te110p with Suse 9.2 on Siemens primergy. We're connecting to voxsteam i60 to test PRI interface. We have problems, after reboot sometimes it goes green, otherwise stays blinking red. How could we debug this situation ? Are there any common advices what to check ? Are CVS Head drivers better than CVS stable ? Why ? Do you also experience such unstable behaviour

We are having line noise issues in our Asterisk to legacy PBX integration. All SIP calls originating from IP phones sound crystal clear. All calls that originate from the legacy PBX (Isoetec 228) and route through the Asterisk and out SIP have a lot of line noise. I believe I have it pinned down to these Blue Alarm errors that I can see on the legacy PBX side. zttool shows no alarm but when I

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

I have a hfc-usb adapter connected to a Samsung PBX, and am having a bit of trouble. With capi, using 'immediate' mode, I can get the dialplan working just fine, except that there is some sort of interference in the audio, and I'm not quite sure how to describe it except that it's sort of like clicking and popping but not harsh at all, and more like just bits of audio missing.

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits

hi eveybody, after many test with your help and the irc channels help, i get the led on TE110P green with this config: span=1,1,0,ccs,ami =====> alarms OK Green Led but the provider say that i have to set my span to this span=1,1,0,ccs,hdb3,crc4 =====> alarms: YEL/RED i can't make call's yet to test because they have to sync the Modulator in the other side so any remark? is my

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello all, Has anyone use the Supermicro PDSME+ in combination with the TE110P successfully? My experience so far is not very good. I am running trixbox 2.0 but: 1) with zttool I am getting IRQ Misses. Don't seem to have IRQ conflict, but I am now running my SATA HD in DMA. And I am not able to set it in DMA(HIO... operation not permitted) 2) With zttool the Alarm is RED 3) When I do the

Hi, I was going to order the T100P but it is replaced by TE110P. On further reading the TE110P does not need an external router (The one that separates the data from pstn lines ?). Has anyone got it configured? And on the wiki it says that the drivers for some distros don't exist yet. Is redhat supported? And if I need to connect a fax machine will the FXO cards on ebay work (I know to

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P