similar to: T1 versus PRI

Hello, We currently have a scenario where a large percentage of inbound calls on a telco PRI are intended for professors who aren't currently in their offices/at their desks. My question is, is anyone actively using the Asterisk "RLT" (Release Link Trunking) feature to bounce these sorts of calls back to the telco? The idea being to forward the call to their mobile phone without

I'd be grateful if anyone here could comment knowledgeably on an idea that I have had, as to whether it should be possible or not. Consider two Asterisk boxes, each with one or more E1s on EuroISDN. Each box has a different telephone number that hunts across all its E1 channels. In addition there is another number that hunts across all the channels on all the boxes. A call comes in to one of

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

Hi Guys, I am sorry if my issue is not related to this but I think it is. I have a PRI with Bell Canada and when I dial in and have the call transfered to a context to dial out and then have those two channels bridged, the call disconnects with cause 16 just exactly as Jay R. Ashworth shows in his CLI output. Bell Canada support RLT or know as 2BCT or TBCT to some but we have not requested that

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

I have not been able to get two B-channel transfer to work on DMS100 PRI. I consistently get the following errors: [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: ROSE RETURN ERROR: [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: OPERATION: RLT_OPERATION_IND [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: ERROR: RLT Not Allowed I have tried on two

When people call into my * box over the T1 interface, they get no ring tone. It rings the SIP phone and when the SIP user picks up, both parties can hear each other ok, its just the PSTN user calling in hears no ring. What could be causing this? I tried setting immediate to yes in zapata.conf, but that causes my DNIS and CallerID to stop being available. T100P with E & M Wink start

I'm trying to get "blind transfer" from an incoming DAHDI line to an external number to work on an * 1.6 install using a T1 from XO. The documentation is very "distributed" and incomplete, so while it's not working, it's definitely more likely my error somehow. Couple questions if anybody is out there who even knows what TBCT is. 1) Is this even

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

List, Having a little trouble with the following. Let me prefix by saying I have blind transfers working from the following setup. Inbound call [from-zap] (SIP/sv0071iv) answers. Zaptel -> Asterisk -> SIP extension SIP extension then blind transfers [from-sip] --- SIP extension -> Asterisk -> Zaptel During this whole process, the original channel off the trunk (lineside T1) is

I installed a Sangoma card with the default install. I'm getting five digits of DNIS with each call. The T1 is setup ESF/B8ZS wink start. Each of the digits of the DNIS are being used for extensions in the context. I need a single extension that let me start an AGI script that can use the dnis. Can anyone point me in the right direction to do this? Thanks, David Ruggles CCNA MCSE (NT) CNA

Hey Don, How are you? I may be heading your way in the next month or so. Have to meet with a guy in Eden Prairie, and stop off at my brother/sisterm-in-law's as well. Got a question for you - with TBCT, who pays for the call once it is transferred? Still me as the owner of the trunk? Lets say I take a call that was dialled locally (caller believes this is "free"), and I do a

Greetings, This may be a bit arcane but does anyone know what the contents of a facility message should be for initiating a TBCT on an NI2 ISDN. I've been trying to get it to work on a DMS100 for the last four months to no avail. The message I am currently sending makes it to the switch but is returned with unknown message. Perhaps someone here has done it before and can help me out.

Thanks AJ and David, We were actually using GSM gateways by setting busy forward number on the SIMs and just giving busy signal on every incoming call, telco took care of the forwarding and the line was free within seconds. Now we need to scale up the setup but GSM gateways a very very expensive if we want to scale upto a 1000 DIDs, which means thousand SIMs and a gateway/gateways big enough.

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

Hello, A client has asked for Two B channel Transfer capability (known as TBCT or 2BCT, similar to other features such as ECT, RTL and Q,SIG Path Replacement) in a new Asterisk system and so I researched the capability and came up with quite a few gaps in documentation.

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system