similar to: Does anyone run Asterisk on FC4? with Digium's TDM40B cards

Morning, I've installed asterisk on FC4 and had a few problems with zaptel stuff. Having installed it on SuSE I was able to check a few things that were different. When installed with the RPMS, the udev stuff gets put into the normal 50-udev file under /etc/udev. On SuSE, it worked when the necessary zaptel section was in a separate file name 55-zaptel.udev (the name is arbitrary,

Dear all, I am happy to tell you that I received a Digium's TDM20B card for my Asterisk box today. but the phone jack is RJ45 instead of RJ11. So Please I need precise instructions to connect a phone to this card. please, assume that I have a phone (a normal analouge phone connected to the one end of a cable with an RJ11 jack (at the phone side). and now I want to connect the other end to the

Greeting!, I read somewhere that without cdr, Mysql etc it is possible to take outgoing-call-logs to a text file. (I am not sure please). is it really possible ? if so, how do I do it? any links to refer? Thank you. Kumara

Hi All, I have this codec problem, I use "gsm" in my iax.conf file and in teliax settings also, but the error is still appearing as below. please help me. Kumara Starting simple switch on 'Zap/1-1' -- Executing Dial("Zap/1-1","IAX2/kumara@teliax/01194777070239|30|tr") in new stack -- Called kumara@teliax/01194777070239 -- Call accepted by

Hi all, again, with another question ( may be the final one) I have come up to this point, means when I dial a number in my analogue (panasonic) phone I hear the ring at the end through my asterisk box (via TDM20B card) that uses IAX2 over teliax and after time-out, it gives this message. Starting simple switch on 'Zap/1-1' -- Executing

Hi all, I'm new to the forum. Oh no....newbie question coming, I hear you all cry! I'm playing around with Asterisk@home and have installed software and fiddled around with sip and extensions files. I have manage to make out going calls through Sipgate using X-Lite but cannot for some reason receive incoming calls. Incoming calls do not even show up on the switchboard panel. I've

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

OK, I have a Asterisk @ Home 1.0.7 server with two Digium TDM400 cards, one 4 port FXO and one 4 port FXS. When I plug an analog cordless phone into the TDM40B card and setup a ZAP extension, the phone rings in and you can answer just fine. The weird part is when you try to get dialtone from the cordless handset it rings all of the other extensions... One other thing to mention is that the

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not

See: http://lists.digium.com/pipermail/asterisk-users/2004-September/063348.h tml -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kumara Jayaweera Sent: Tuesday, June 14, 2005 1:46 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] RJ45 instead RJ11 in Digium's TDM20B card help meplease

Hi Openssh support, I have upgraded openssh from 5.3p1 to 6.2p2 in a RHEL 6.6 - 64 bit server and now i can't login to server remotely using same root password. It always prompting the password saying "Permission denied, please try again." Please help me to resolve the issue. Following are the steps i have followd.

Hi everyone, Sorry for forwarding and top-posting this email again but its as if my TDM40b has keeled over yesterday. After a few hours last night and swapping the card to another asterisk server (with exactly the same result) I needed to have the FXS ports working ASAP this morning so I have repaced the functionality of the TDM40b with some Grandstream handytones which I already had in

Hi ! I have a TDM40B and i try to use it connected to modem for incoming call data transfert. I have no problem to use it with a phone and a talk communication work fine. But when we try to use with modem, with most modem, we got data carrier for few seconds and channel hungup. < [ TYPE: Null Frame (4) SUBCLASS: N/A (3) ] [Zap/4-1] -- Zap/4-1 is ringing << [ TYPE: Null Frame

We are using TDM40B's to connect some devices to Asterisk which depend on caller information arriving as ANI, rather than as Caller ID. I am unsure if the TDM40B supports this in the first place, and if so, I am unsure how to configure it so. I've searched the wiki but couldn't find anything. Can someone please confirm whether or not this is possible? As a fallback I could reconfigure

Hi. I was testing my brand new TDM40B and noticed that when the kernel module is loaded (so the card is powered on), the chip onto the ringer module (the one below the S/N label) is pretty hot (I can't touch it for more than 2 seconds). Is that normal ? Or too much hot could be dangerous ? Matteo Matteo Brancaleoni Espia - Emmegi Sys Admin http://www.espia.it

I have 2 xp100's and one TDM400P. I've plugged a phone into the tdm40b, and when i take it off hook sometimes i get a dialtone, other times i get the message "Power alarm of module2, resetting" spit out to the console from the wcfxs driver does anyone know what this could be? I've tried two different phones, with the same result on both. I changed the signalling to

Hi, I get the following message when I try to run Asterisk. This happened after I changed some of the configuration files: extensions.conf, zaptel.conf and zapata.conf. I have both TDM40B and X100P cards and am trying to use them together. Please let me know if there is something else I should do. Thnx, Gladys [chan_local.so] => (Local Proxy Channel) == Registered channel type

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase