similar to: OT: Hottie ?!?

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 8351 bytes Desc: image001.gif Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050601/65fd0455/attachment.gif

Hi Everyone, So I have been further exploring the integration of our asterisk server and our lucent definity g3si system. I took the suggestion of setting up an isdn-pri line added the two way tie trunk and the signalling group, but can't seem to get the PRI signalling working on the asterisk correctly. I've set pri type to network on the lucent, and pri_cpe in zapata on the asterisk, but

Hullo over there. i'm trying to link an asterisk box with a legacy PBX system with a four wire trunk line. the legacy PBX has 21 analog phones connected to it and i would like to route calls to another site via the asterisk box. i would like to use E&M signaling over this line. my question is how many simultaneous calls can you have over this line with E&M signaling. is there a better

OpenSSH 5.1p1 I can't grasp why, when connecting with 'ssh -Y' to this test host, I am not tickling the verbose() call below that I have added. I am logging as auth + verbose in sshd_config The X11 forward for the session works fine as tested with xterm. At any rate, I am looking for some guidance on where to log X11 forwards that are established, ideally with a username and remote

Calling all Definity admins, Got a few questions about Definity -> Asterisk interoperability. 1) What are the options for integration? Can I hand off extensions from the Definity and vice versa? 2) Anybody have any working configs they would like to post? I've found and read the legacy integration on the wiki about the two systems. I've also googled and found a few threads that were

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Does anyone know if the HandyTone 486 has the option to turn the two ethernet ports into either a switch/hub, or does it have to do NAT ? Thank you, Steve Maroney

I need to connect up to sixteen phones per building, I can use a cheap hub, but POE would be useful. Is there a cheap POE hub available? Everything I have seen has been expensive. Chris Mason

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

Hey guys, I was wondering what POE solutions are being used ? Ive done some searching on google and found that PowerDsine seems to be good brand. Any comments,suggestions, and experiences on POE hubs other POE products would be greatly appreciated. Thank you, Steve Maroney

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Im trying to get IAX to work between my * and FWD. I activated my iax2 account on iax.fwdnet.net and I get the output: "Registered to '65.39.205.121', who sees us as 68.14.203.254:4569" when I start asterisk. I tried used the Call Me tool on fwdnet.net but I dont get any calls even though the Call Me tool says everything looks ok. Can someone call my FWD number and just leave

Im looking for an Intercom solution thats interoperable wit Asterisk. Ive read several posts about people using the 2nd lines on some SIP phones w/speaker phone. Unfortunatley I dont that is going to cut it in a large warehouse enviroment. Does anyone have a solution that uses a "loudspeaker" ? Thank you, Steve Maroney

All, I have done research on VoIP for some time now. I'm a Cisco certified Network Engineer however Telecom is not my strongest suit. I've been a part of this mailing list for sometime but my delusions of grandeur in migrating our 25 year old phone system to a new platform have been on the back burner, until now. I have found my company is moving to a new location(building) and this

Hey guys, Im interested in hearing about servers (and thier hardware specs) that successfully run both asterisk and samba for an office of maybe about 12 extensions (SIP) and about 12 workstations. Im hopeing to not only replace a traditional PBXs with Asterisk/Linux but to provide a solution to needs such as a file serving, email serving, etc. Ive read the Success stories form voip-info.org but

Hey guys, Im about to sign up for VoicePulse Connect. Of course, I plan on using my asterisk server to "register =>" with the service. I would rather sign up with VoicePulse via SIP instead of VoicePulse Connect. My asterisk box is behind another Linux box serving as my nat/firewall. Does anybody think I will have a problem ? Should I stick to IAX and VoicePulse Connect or can I use

Hi, Anybody have an idea how to integrate * with a Panasonic td-1232? We one at the main office, and are installing * in a branch office. We'd like to be able to make calls from * extensions to Panasonic extensions and the other way around. Making outgoing calls from extensions one one side to lines on the other would be nice too. I can put another * machine at the main office, but what is