similar to: Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode?

Maybe this is rather a hardware question, but I am posting it on this list because the probability of someone else of you having tried this is greater here than other places I can think of. I have an ISDN card that is setup in NT mode using the zaphfc driver in bristuff, and I got it working perfectly with one ISDN phone using a crossover cable and 100 ohm termination at the end of the cable.

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

I would like to know how to install asterisk 1.0.9 with zaphfc working on a SuSE 9.2. I tried this: - The rpms with SuSE 9.2 are asterisk 1.0.6 - bristuff works, except for zaphfc, which doesn't compile. - The official asterisk download file doesn't contain isdn bri support Any ideas? Lars Dybdahl.

Hi - Anyone using zaphfc cards (bri-stuff-0.0.2) on a Portugal Telecom BRI service? I am getting loads of errors and the audio is very distorted all the time. System is a Dell PIII/933 MHZ with SCSI. Here in the UK we have perfect audio with a Compaq PIII/500 MHZ SCSI system. Files are identical in both systems as below: Is there anything magic about Portuguese ISDN? The PCI bus in the

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

Since the X100P/X101P/Clone cards does not work in all countries that use DTMF based Caller-ID systems, I've developed a hardware that you connect to a serial port and the PSTN. You then run a perl script "cid_logger.pl" as a daemon, and modify extensions.conf to call an agi script whenever a call comes in, and if it's on the X100 card it will get the caller id information

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

Hello list, I'm trying to use zaphfc, the module loads ok, and it identifies the hfc boards in the machine. The problem is: whenever i try to ztcfg -vv I get the following: 8x------------------- Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual