similar to: PRI Channel Question

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Good Day list, I have googled and wiki'd myself to no avail. Here is my setup. Asterisk Box Digium T1 card connected to an adtran Total Access 624. I need to pass ANI and DNIS information from asterisk to the analog devices hanging off the adtran. The digits are announced to the fxs devices between ring 1 and ring 2 (If I pick up the anlog phone after ring 1, I can hear them so I

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

I have two Adtran 750's connecting our analog phones to asterisk. On occasion, I get a channel that gets "stuck" off hook. 'show channels' shows: Zap/27-1 (longdistance s 1 ) Rsrvd (None) (None) And will just stay like that until the phone is manually picked up and hung up again (or asterisk is stopped/started). I guess this is a function of an unclean hangup (being

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

Hello! We are using the Digium 405PP card, and getting the following messages: Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 8 on Primary D-channel of span 1 My config file is below. We are trying to set up D-Channel on channel 24, 1-23 in trunk group 1,

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

All, Alright, I've looked around the internet, the voip-info.org wiki, and browsed the contents of this mailing list. While I've found a couple of scenarios that are close to this one, I haven't found one that uses my particular card (T100P). Without further delay -- I have successfully configured internal SIP services between a Snom 200 and a Windows X-Lite client and have

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

When I send a call from my TE410P using E&M, the legacy PBX answers the call but doesn't route it. Any idea what this could be? I assume the digits aren't being delivered properly to the legacy pbx. Any suggestions on what config settings to muck with? Asterisk SVN-branch-1.2-r40901 built by root @ pbx04 on a i686 running Linux on 2007-01-14 14:05:02 UTC zaptel.conf

I'm having problems with unclean hangups (being read as a flash instead of a hangup?). Can I turn off hook flash recognition in asterisk, but still have the flash button on the analog phone operational? Could I use these settings in zapata.conf to fix my problem? *prewink*: Sets the pre-wink timing. *preflash*: Sets the pre-flash timing. *wink*: Sets the wink timing. *rxwink*: Sets the

Hi, Is there any documentation on the fields prewink, preflash, wink, flash, rxwink, rxflash, start and debounce in zapata.conf? The "Recall" button on my phone doesn't seem to trigger a transfer via my shiny new TDM40B. However, tapping the hook does, but only if I tap it for long enough. Presumably the "Recall" button's timing is too short? Further, most users who

Hey Everyone, So this is a problem I've been having for sometime now. I sent a few messages to the list with no luck. The problem is that when people dial into the Asterisk system using DID numbers, it works the first time or 2, then I get busy signals. A friend recommended I clear out the zapata and zaptel, start over, and recreate my wanpipe stuff. He thought the problem was with the spans

Hi, I have this error, I have a digium card TE110P Tiger3xx When I'm load the dirvers by this command modprobe wcte11xp I got this error "Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wct1xxp " when I'm Lunch the command ztcfg -vv I got this error.