similar to: G729 - What versions can Asterisk support?

I am thinking about using the G729 codecs on my endpoint devices and purchasing some G729 licenses for Asterisk but I have several questions: 1. Which G729 codec is sold by Digium for Asterisk, G729, G729A, B...I? 2. If I have G729A on one end and G729B on the other, are they compatible? I have looked all over the place for question 2, but without buying the ITU docs I cannot seem to find this

I own a G729b codec from voiceage which I had from Digium a couple of months ago , I friend of mine had the new Digium G729 codec which registers in the asterisk as a Annex A/B codec, the problem that we saw is that the call goes thru find but we cannot here any sound. Asterisk is showing this : -- SIP/10.10.1.1-babc is ringing -- SIP/10.10.1.1-babc answered

Hello! I am wondering how the differences between G729, G729a, and G729b effect call bridging and server interoperability. For example, can one server use the G729 code with another server that uses the G729A codec? Also, which version is Asterisk set up to use? Thanks! Elliot

Hi all, i have purchased the g.729 codec from digium. The registration was successful. (with the "old" binary) But there're a few questions: - should not the codec listed in the codec list when i enter "show codecs" ? - the codec is named with g729b but if i enter show codecs there is a codec g729a listed also the g729b is not installed. what is the difference between

Hello all, I have a cisco AS5300 which is register with a gatekeeper and a Asterisk server also register with the gatekeeper. PSTN ---->AS5300 ---->Gatekeeper ---->Asterisk I set up a conference room on the Asterisk sever (Room No 1234). I try to call from PSTN to AS5300, The AS5300 will call the Asterisk server through the gatekeeper. I manage to get to the start of the conference

Hello.... I have the follow situatuion: < ISDN > | | V E100P |----------------| IAX2 / g729A |----------------| T100P | Asterisk1 |- - - - - - - - - - - - - - > | Asterisk2 | - - - - - -> |--------------| | | | | | Zhone | ----------------- ----------------- --------------- Here's the situation: I receive calls from the PSTN

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

Hi, I've oh323 chan installed and working to make calls from SIP to H323 devices. The problem is can no hear sound with the H323 device. I think this is some related with codecs o nat, because the H323 have one public IP from a different subnet from the asterisk box. If I use netmeeting in gateway mode, the call can be completed and I can talk with a SIP device, but in gateway mode I can not

Per my conversation below with digium, are there any legal alternatives to digium's G729? It is out of date, and doesn't support VAD nor silence detection. Digium has stated that they have no plans to update it anytime soon. VAD/Silence is a big deal with major carriers and we are having to fight a battle to get them to make special arrangements to turn off VAD/Silence in their

Hi all, i have big problems to make a h323 call over the gatekeeper from my provider. The provider demanded following account data: H323 ID: XXX-XXX-XX-X DetinationNumer: XXXXXXXXXXX I have configured the oh323.conf following: gatekeeper=XX.XX.XXX.XXX alias=XXX-XXX-XX-X Isx the alias equal to the h323id ? And how i have to make a call with the dial app ? I have following config: exten

Hello All, I looked at the codec supplied by Digium and I think that it is G.729 Annex-B (G.729b - 8kbps). Correct me if I'm wrong. I have also looked at the article from Cisco "VOIP Understanding Codecs: Complexity, Hardware Support, MOS, and Negotiation", which states that G.729b is supported on pretty much everything except for AS5350/5400. Also that G.729b is a "high

Hello, I managed to terminate calls from cisco: as5300 and 7206 to asterisk over h323. I tested both oh323 from inaccessnetwork and JerJers chan_h323. I used 1.12.2 version of oh323 and 1.5.2 version of pwlib. After latest changes from JerJer chan_h323.c works ok when receiving traffic from ciscos. I havnt found any audio problems although I didnt send much traffic. Latest oh323 has some

What is the configuration of H323.conf and openphone in order to run openphone and asterisk together ?

Folks! I would appreciate if someone could send me a simple working h323 configuration file oh323.conf that is part of asterisk@home installation. I have tried to use the oh323.conf content listed on WIKI but it is just not working as my H323 endpoint ( PA168 based ATCOM Phone) cannot register. I need a working example of this file for similar phone. Seshu

According to digium's site, "Note: Please do not attempt to use the G.729 code in a SCSI-only system. We are currently working with VoiceAge to correct this issue." (found at http://www.digium.com/index.php?menu=asterisk_g729). Does anyone know what these issues are? Can anyone define SCSI-only system? I know this sounds kinda dumb, but I have a server with SCSI and IDE interfaces,

Hello, I have 5 digium's g.729 codecs and succesfully register with asterisk, I have incomming call from my cisco AS5300 to Asterisk through IP. But Asterisk always use g711 ulaw instead of g.729. When I disable all other codecs other than g.729 in both cisco and asterisk, calls get dropped once connected. The codec list show on my cisco AS5300 for g.729 are: g729r8 g729br8 I suspect that

Having purchased a license for 5 g729 channels on Digium's web shop I thought registration and installation would be a snap. NOT. I followed registration instructions to the letter but it failed with that message: ERROR! Your Internet connection is probably behind a proxy and the Registration program can't communicate with our server Which is stupid as my * box is a firewall and sits

Hi, i have a problem trying to register the codec G729, my licence is valid but when i try to Register i got the following error: "Registration unsuccessful... Error code: 110 ERROR! Your Internet connection is probably behind a proxy and the Registration program can't communicate with our server, however it has created the file: /var/lib/va-infoclient

I have multiple voiceage g729 licenses installed on a RH9 box, and have a remote C7960 configured to use it (low bandwidth). In calls like: Remote C7960 -> g729 -> asterisk -> g711 -> C7960 the audio is oftentimes rather choppy. Changing the remote 7960 to use g711 seems to eliminate/reduce the choppyness. Any ideas on what might be behind this?

I want use iLBC and have following in mind, please help me is it possible ? ISDN <-----(ALAW)-----> * <-----(ALAW)-----> SNOM SIP??<-----(iLBC)----->?*?<-----(ALAW)----->?SNOM 1. ISDN incoming codec is ALAW SNOM codec should be ALAW (can't be iLBC because a lack of codec). 2. SIP incoming codec should be iLBC (snom is ALAW). 3. SIP outgoing codec should be iLBC /snom