similar to: Asterisk stop working with HiSAX ISDN

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV

I'm trying using Asterisk over an isdn line. I configured my Eicon Diva card by the hisax module and it works with the Asterisk's chan_modem (and chan_modem_i4l) driver. The problem is that I can receive calls (on /dev/ttyI0) but when I make a call I always have the line busy (on ttyI0 but even if I use an other device like ttyI1). This is a part of my consol output: --

I need HELP pls! BRISTUFF: Bad Sound quality CAPI : PTP Mode dont supported mISDN : kernel is 2.4.x and not 2.6.x HISAX : PTMP ok, PTP incoming ok but in outgoing asterisk dont compose number(i listen dial tone and than i can compose number via dtmf) Asterisk CLI (g3 is group of Modem[i4l]/ttyI0 and ttyI1): Called g3: 3453444444

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

I'm trying to get a basic Asterisk configuration together for ISDN incoming / outgoing calls. I have two Cisco 7905g phones working (at least talking to each other) and have purchased a NETjet-S PCI ISDN card for routing calls to / from ISDN. The state I've managed to get it to is:- -- Executing Ringing("SIP/PHONE2-d557", "") in new stack -- Executing

We have setup an asterisk box to let everybody call into the university internal network, but I get unexpected hangups when doing an outbound call from SIP to the ISDN interface, and it happens from 20 seconds to some minutes into the call. ----------the dial and the problem----------- -- Executing Dial("SIP/57966-a19d", "Modem/g1:96121||rt|") in new stack --

Currently we have problems with our asterisk server connect with an Eicon Diva 4BRI Card to a PBX. Asterisk is running in version 1.0.0 on RedHat Enterprise Linux 3AS with kernel 2.4.21-4.EL. The Diva server is running in version 7.5 Can someone help us in reolving the errors with incoming calls? When we try to call to an extension we get these messages in the CLI: -- creating pipe for

Hello, I am trying to use 2 netjet cards under asterisk and isdn4linux. I am having a hard time trying to get them to work in terms of dial out. Does anyone have a working config I could look at for even one card (tried that, not much luck either). When i dial out: -- Accepting AUTHENTICATED call from 172.16.11.2, requested format = 2, actual format = 2 -- Executing

I have installed a Billion ISDN card in my Asterisk. Calls between sip and isdn work. The i4l channel has MSN=26. I also put incomingmsn=26,27 in modem.conf. extensions.con: [incoming-isdn] exten => s,1,Dial(SIP/701,20,Ttr) ;will make my extension 701 ring, while exten => 26,1,Dial(SIP/701,20,Ttr) ;will cause an error message in the Cli interface: WARNING[196621]: pbx.c:1814

G'day, New to Asterisk alert! I have a Netjet card running on linux 2.4.27 kernel using the HiSax module, and trying to use it for incoming/outgoing calls from *. I've tried playing with modem.conf and extensions.conf every which way I can think of, using samples and whatever I can find off the net, and I get the same message everytime I try to dial in. The complete message is:

Greetings, today I'm recompiling asterisk on a new machine with the same isdn card (not the same model, the *SAME* card) using CVS downloaded yesterday night. When I try to start *, it gives me the error: [chan_modem.so] => (Generic Voice Modem Driver) == Parsing '/etc/asterisk/modem.conf': Found == Loading modem driver chan_modem_i4l.so => (ISDN4Linux Emulated Modem

Hi to everyone! I am new to this list and i want to greet you all! I am trying to install Asterisk on a Fedora Core 3 Distribution with a Digi Datafire Micro V ISDN Card. I know that I have to use the ISDN4Linux so in modem.conf I set the I4l driver ,the msn and device. Modem.conf [interfaces] context=remote ;driver=aopen ; modem by AOpen driver=i4l ; isdn4linux - an

Sorry for a slightly off-topic question, but I'm getting desperate. I tried to use asterisk to talk w/ ISDN line and tracked the problem to i4l. I have a Diva PCI 2.02 (S/T) card and am running RH8 w/ 2.4.20 kernel (first version that supports the 2.02 w/ hisax driver). The switch is a 5ESS running NI-1 protocol. The card sync's up and reports other traffic on the line, but fails to

Hi Thomas, I saw your mail to Asterisk mailing list regarding ISDN BRI problem. It was about answering the call. I'm facing a similar problem. I had briefed the problem below. Please tell me what are the parameters to check/change to get it working. I have Hisax ISDN BRI card. I configured extension.conf, modem.conf correctly and could make outward dialing. But when I make incoming call

Hi, I have a problem that I just can't figure out how to solve. I start *, dial it using a ISDN phone over PSTM, to a Hisax card installed in * I get the demo-greeting, listen for a few seconds and hang up. I dial it again, but this time the first second is sound from where the previous call ended, then the greeting starts as it should. Right now I have removed all codecs but codec_gsm.so

In this message I try to summarize what I have learned in these last two weeks. My primary sources of informations were the * list archives and linux ISDN docs. I ain't no * master, so don't trust too hard. Relevant messages from the * list for the current discussion are: 009177.html 009268.html 0498.html 0849.html My setup is an Eicon Diva (HiSax: Eicon.Diehl Diva driver Rev. 1.1.4.2)

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

I have * with i4l installed and working - on a dumb eicon card. It seems in order to get DTMF out of the BRI (for business banking - etc) - I should change from i4l drivers to capi drivers. wiki help seems to be for the Fritz card only...??? I have ticked the suggested boxes in 'menuconfig', explored the capi4linux websites - etc... but am missing some magic. I've "modprobe