similar to: MAKEing zaptel and ztdummy on SuSE 9.3 - Repost

Hi, I'm following the instructions on Asterisk Doc Proj: astersik_1.0.8/docs/docs-html_one/vm1.html#AEN30 and they don't seem to work out. The order suggested is: cd zaptel make clean make linux26 make install vi Makefile (and uncomment ztdummy) make modprobe zaptel modprobe ztdummy The first 3 makes for zaptel work out ok - but the ztdummy.ko (etc) files *are* created. If the

Hi Guys I have been running a test server for a few days now with * 1.0.9 bristuff RC8n. I had a power failure and the test machine was not on the ups. When power was restored I found the following error: FATAL: Error inserting zaphfc (/lib/modules/2.6.11.4-20a-default/misc/zaphfc.ko): Unknown symbol in module, or unknown parameter (see dmesg) My dmesg output: zaphfc: unsupported

Hi to everybody, seems that I cannot load the zaptel modules: ztdummy says the following: [root@Hayabusa misc]# modprobe ztdummy /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.22/misc/ztdummy.o: unresolved symbol zt_register

Hi, ztdummy says the following: VoiceBOX:/usr/src/zaptel# modprobe ztdummy /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.18/misc/ztdummy.o: unresolved symbol zt_register /lib/modules/2.4.18/misc/ztdummy.o: insmod

Hi! When I try to load the ztdummy driver via "insmod ztdummy", I get the following errors: /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_register I'm using zaptel-1.0.8 and

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi, >However, I believe that zaptel >= 1.4.6 or zaptel 1.2 >= 1.2.21 should >support hires timers for timing on kernel >= 2.6.22 . > >What version of Zaptel do you use? > I was using version 1.4.5.1 I just downloaded and installed version 1.4.7, configure/make/make install finished without an error, but when is used modprobe ztdummy the system said: FATAL: Error

Hi all, Trying to build ztdummy on an old redhat 7.3 box running kernel 2.4.20-43.7.legacysmp. Yes, I have the kernel sources installed. Yes, I set them up with make oldconfig; make dep. The build error is: make ztdummy gcc -I/usr/src/linux-2.4/include -O6 -DMODULE -D__KERNEL__ -DEXPORT_SYMTAB -I/usr/src/linux/drivers/net -Wall -I. -Wstrict-prototypes -fomit-frame-pointer -I/usr/src/

I'm chasing down a pop/click type of disturbance on a PBX system. Strangely, the disturbance is only heard by the outside caller, the internal recipient hears the caller crystal clear. This seems to have crept up when upgrading the zaptel driver to the 1.2 series while running 1.0.10. I went ahead and upgraded the entire system to 1.2.4. The system is a ~2Ghz AMD 32bit system, with 512MB of

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

I get this warnings while compiling zaptel Any suggestions would be very helpfull. make -C /usr/src/linux-2.6 SUBDIRS=/usr/src/bri-stuff.0.1.0-RC4/zaptel modules make[1]: Entering directory `/usr/src/linux-2.6.8.1' CC [M] /usr/src/bri-stuff.0.1.0-RC4/zaptel/zaptel.o /usr/src/bri-stuff.0.1.0-RC4/zaptel/zaptel.c:163: warning: `fcstab' defined but not used CC [M]

Hello everybody, Please, help to fix me a problem. I have a distributed-replicated volume between two servers. On each server I have 2 RAID-10 arrays, that replicated between servers. Brick gl1:/mnt/brick1/gm0 49153 0 Y 13910 Brick gl0:/mnt/brick0/gm0 N/A N/A N N/A Brick gl0:/mnt/brick1/gm0 N/A

Hi Everyone, I read through the list on the issues with the ztdummy driver which I need for MeetMe, but I seem to have come across a problem that I cannot seem to find an answer for. I am running Gentoo 2.6.10 on an Intel box. I have read the the wiki entries on the ztdummy and followed the instructions as they relate to the 2.6 kernel. Everything compiled great, but a modprobe ztdummy

Hi, I'm running SuSE 9.3 fully updated using YOU and I *have* re-booted the box (in a hope to sort out the uname -r issue mentioned below). I'm using the Asterisk Doc Proj vol 1 to guide me through the initial setup. I have no special HW and intend to use asterisk on an internal network just to get some experience. I have downloaded what I think I need and placed it in /usr/src (see

hi All, There is a distributed cluster with 5 bricks: gl0 Filesystem Size Used Avail Use% Mounted on /dev/sda4 5.5T 4.1T 1.5T 75% /mnt/brick1 gl1 Filesystem Size Used Avail Use% Mounted on /dev/sda4 5.5T 4.3T 1.3T 78% /mnt/brick1 gl2 Filesystem Size Used Avail Use% Mounted on /dev/sda4 5.5T 4.1T 1.4T 76% /mnt/brick1 gl3 Filesystem Size Used

I got a new motherboard and upgraded Asterisk, ... However, I am not lucky enough to get it running again. To compile went ok, besides this remark at the end of asterisk: WARNING WARNING WARNING Your Asterisk modules directory, located at /usr/lib/asterisk/modules contains modules that were not installed by this version of Asterisk. Please ensure that these modules are compatible with

This is a patch that I've had kicking around that I never sent in. With it applied I can compile the module programs from module-init-tools: diff -uNr klibc-0.178/include/sys/elf32.h klibc-0.178-fogo/include/sys/elf32.h --- klibc-0.178/include/sys/elf32.h 2004-01-30 14:40:51.000000000 -0700 +++ klibc-0.178-fogo/include/sys/elf32.h 2004-09-20 09:15:58.000000000 -0600 @@ -7,6 +7,10 @@

Hi all, I hope everyone is doing well. I just joined the list, and I've really enjoyed all I have read about asterisk so far. Unfortunately, I'm having a bit of trouble implementing this thing :). By the way ... I did my best to search the forums, and also to use google extensively, and while I have found pages with people with the same problem, ... The fix suggested on those sites,

I downloaded the cvs development of zaptel... It seems to compile ok, but when ismod I get: lp:/usr/local/src/zaptel# /sbin/insmod wcfxo.o wcfxo.o: unresolved symbol zt_ec_chunk wcfxo.o: unresolved symbol zt_unregister wcfxo.o: unresolved symbol zt_alarm_notify wcfxo.o: unresolved symbol zt_hooksig wcfxo.o: unresolved symbol zt_transmit wcfxo.o: unresolved symbol zt_receive wcfxo.o: unresolved

You where SOO right. My idea is to connect the "line" to my pbx and call from internet (h323?) to my linux box, and then dial an extension.. Is there any doc there? Cause Ive read a few and I did not get much really. I should configure asterisk now and the job is done? -----Mensaje original----- De: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] En