similar to: MAKEing zaptel and ztdummy

Hi, Sorry to re-post, but I'm still having hassles with ztdummy. I'm using kernel 2.6.11.4-21.7-smp and Asterisk 1.0.8 on SuSE 9.3 The first 3 makes (see below) for zaptel work out ok - but the ztdummy.ko (etc) files *are* created even though I haven't yet uncommented ztdummy in Makefile. If the ztdummy bits are compiled, why edit Makefile & run make again? modprobe ztdummy

Hi i followed this instructions for installing ztdummy on a 2.6 kernel (taken from http://www.voip-info.org/wiki/index.php?page=Asterisk+timer+ztdummy ) cd /usr/src/zaptel * READ /usr/src/zaptel/README.udev and follow the steps * check modules on: /etc/sysconfig/zaptel> if you have no digium hardware comment out all modeules except ztdummy. - make linux26 - make install -

Hi all, I have a problem starting the ztdummy. Here is what happens: [root@asterisk /]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy After this, ztdummy is visible with lsmod, but when I try MeetMe, I get following: == Parsing

I have several servers using ztdummy as the timing source, some CentOS 4.x, some CentOS 5.x, some Asterisk 1.2.x, some Asterisk 1.4.x. "zap show status" differs between the servers: ZTDUMMY/1 (source: Linux26) 1 UNCONFIGUR 0 0 0 ZTDUMMY/1 (source: RTC) 1 UNCONFIGUR 0 0 0 ZTDUMMY/1 1 UNCONFIGUR 0

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

Hello, Maybe I'm missing something here. What is the proper way to use RTC with ztdummy now? I'm using -HEAD from a day or two ago on Linux 2.6.11.11. In zaptel/Makefile, I changed CFLAGS to: CFLAGS+=-I. -O4 -g -Wall -DBUILDING_TONEZONE -DUSE_RTC #-DTONEZONE_DRIVER and I get.. make -C /lib/modules/2.6.11.11/build SUBDIRS=/usr/src/zaptel modules make[1]: Entering directory

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

Hi, Can any point me in the right direction to solve this one? I get a: "this account is not authorized to login from this station" message when I try to "Map Network Drive" from NT4server SP4 to my RH Linux 6.0 Samba 2.0.3, yet I can open a telnet session from the NT machine to Linux using this user, and, in a linux xterm window I can list the samba services using

Folks, I have been trying to install Zaptel 1.4.0 on my SuSE 10.0 box with kernel 2.6.13-15.12. I have installed the kernel sources and run "make cloneconfig" and "make prepare". I have run ./configure but make linux26 is failing with the following error: hawk:/tmp/zaptel-1.4.0 # make linux26 make[1]: Entering directory `/tmp/zaptel-1.4.0/menuselect' make[2]: Entering

Hi, I'm running SuSE 9.3 fully updated using YOU and I *have* re-booted the box (in a hope to sort out the uname -r issue mentioned below). I'm using the Asterisk Doc Proj vol 1 to guide me through the initial setup. I have no special HW and intend to use asterisk on an internal network just to get some experience. I have downloaded what I think I need and placed it in /usr/src (see

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44

Hi Everyone, I read through the list on the issues with the ztdummy driver which I need for MeetMe, but I seem to have come across a problem that I cannot seem to find an answer for. I am running Gentoo 2.6.10 on an Intel box. I have read the the wiki entries on the ztdummy and followed the instructions as they relate to the 2.6 kernel. Everything compiled great, but a modprobe ztdummy

Hi, I'm still strugling with getting an easy to use conference system implemented. I did have app_conference running, but today I upgraded asterisk to 1.0.9 and it stopped working. I've tried following the instructions for compiling app_conference on 1.0.7 but it didn't work. So I went back to ztdummy (I've not had any luck getting this to compile on FC2). Anyhoo, I've

Hi, I've been following a similar and current thread about name resolution from LINUX side. I have exactly the opposite problem (running ubuntu 7.10 on a network with a mixture ubuntu 6.06, WinXP and WinVista boxes) The winboxes cannot see or mount this 7.10 box I can mount WinPC shares on this 7.10 box. I was wondering about firewalls, but I can ping this 7.10 from the WinBox by IP address

I have an asterisk box with no zap hardware in it. I use the ztdummy for music on hold. However, the music is very distorted. I rmmod ztdummy, and the Music sounds great. Michael

Anybody having issues with ztdummy under the current 2.6 RC7? I get the following errors when trying to modprobe ztdummy: "Unable to register zaptel rtc driver" Doing a Google on the error shows reference to a message from 2004 that said you might not have RTC compiled into the kernel. Checking via: cd /usr/src/linux-2.6.13-rc7 grep -i rtc .config shows: CONFIG_APM_RTC_IS_GMT=y

I am (unsuccessfully) trying to install zaptel (incl ztdummy - I don't have any Digium hardware) on CentOS 4. uname -r 2.6.9-42.ELsmp Not sure how this relates to 2.6.9-42.0.3 (see below) ln -s /usr/src/kernels/`uname -r` /usr/src/linux ln -s /usr/src/kernels/`uname -r` /usr/src/linux-2.6 cd /usr/src/zaptel-1.2.11* make linux26 You do not appear to have the sources for the 2.6.9-42.ELsmp

The USB core was completely rewritten in 2.6, and as such the functions that ztdummy depends on do not exist in 2.6. I get the feeling that these changes are too much to easily fix ztdummy, so I don't expect to see it working on 2.6 any time soon (if ever) I made some small changes to zaprtc to work on 2.6 and I have MoH and Meetme functions working fine in my lab. For production I would

Hi all, I hope everyone is doing well. I just joined the list, and I've really enjoyed all I have read about asterisk so far. Unfortunately, I'm having a bit of trouble implementing this thing :). By the way ... I did my best to search the forums, and also to use google extensively, and while I have found pages with people with the same problem, ... The fix suggested on those sites,