similar to: Audiocodes MP-108 FXO to Asterisk HELP

My experience with an MP-108 was similar. Incredibly complex to setup, and very little help from MFR, or even ABPTECH, the main US reseller. We just couldn't get it working properly. Ended up with a TE110P with an Adit 600 channel bank, which ROCKS. Unbelieveably easy to setup. No echo whatsoever. -Darren

I was able to setup AudioCodes MP-114 to rote calls form FOX to Asterisk and make internal calls: Routing Tables -> Tel to IP Routing: *, *, 10.0.0.109 (my asterisk IP) But I'm not sure how to setup AuioCodes to make calls out via FXO? In extensions.conf [Globals] pstn-5665=10.0.0.157 Whenever, I try to call out I get a busy signal. -- Joseph

Hi list, I'm trying to get ready the MP-104 FXO to use qith my box, but when I send calls I hear only dial tone and after a few seconds I get busy signal. I very appreciate your advices. Command line results and SIPconfigurations follows: *CLI>* -- Executing [7991696900 at total:1] Playback("SIP/101-09dd8918", "beep") in new stack -- <SIP/101-09dd8918>

I'm trying to get a MP-114 FXS/FXO gateway working with Asterisk. It registers fine and I can call between the MP-114 and other extensions, but I'm not having much luck with the FXO ports. syslog shows the problem to be in the MP-114 configuration. Can anyone help?

I am currently installing an Audiocodes MP-108 with Asterisk in Singapore. I am able to make outgoing calls but incomming calls just get cut by the MP-108 I can see the corrosponding frontpanel led light p but the call gets cut so I'm very confused about what could be wrong. Could this problem have something to do

Sir, Here is the working Audiocodes MP-11X FXO configurations to work with Asterisk. ;************** ;** Ini File ** ;************** ;Board: MP-118 FXO ;Serial Number: 905371 ;Slot Number: 1 ;Software Version: 5.00A.024 ;DSP Software Version: 204IM => 209.13 ;Board IP Address: 192.168.0.195 ;Board Subnet Mask: 255.255.255.0 ;Board Default Gateway: 192.168.0.1 ;Ram size: 32M Flash size:

Hello, Anyone here have experience with Audiocodes MediaPack MP-108 Gateways? I would be willing to pay someone for advice and support with configuring my gateways for a telemarketing project I am starting. My experience is somewhat limited but all I want to do is make outbound calls just like I would on normal pots lines. (That's the best way to explain it) I do not need any special

Has anyone used the AudioCodes MP-20x? http://audiocodes.com/Objects/Analog_Telephone_Adapter_Series_MP_20X.pdf Seems like a good device, but I can't seem to find anyone actually using them... -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061022/6ca85b8c/attachment.htm

Razza, I have a MP114 FXO/FXS that I have never got to work , even as an FXS, even though I have several other FXS's that work fine ie Linksys PAP2 etc.. would you put up your config? PDE

I've MP-114 that is working configured and working OK with my Asterisk but I just obtained MP-112 (2xFXS) and I can register OK with asterisk but I can only dial 3-digit extension. Anything longer than 3-digits is cut off, example I dial extension 1000: [Apr 29 10:03:30] NOTICE[3817][C-000000e9]: chan_sip.c:25902 handle_request_invite: Call from '54' (10.0.0.115:5060) to extension

I have AudioCodes MP-114 and I'm trying to configure SAS (Stand Alone Survivability); when Asterisk is down the MediaPack gateway should forward the call IN/OUT through the gateway (without asterisk in the middle), but it is not working. I'm working with tech. support from the source I purchase the unit from they we are just emailing back and forth and the unit is still not working. Can

Hi All I have been able to get MP 104 FXO to make outbound calls with my asterisk box and polycom IP 500 phone. However I cannot get the incoming calls to hit the asterisk box. Any help will be appreciated. Thanks, Lal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060612/36de60cc/attachment.htm

I have an Audiocodes MP-114 and modem dial-out can not establish connection. Snooping with Wireshark I get a lot of entries like this: No. Time Source Destination Protocol Info 2934 27.221559 10.0.0.110 10.0.0.109 RTP PT=ITU-T G.711 PCMU, SSRC=0x7D08611A, Seq=7662, Time=1805957855 Frame 2934: 214 bytes on wire (1712 bits),

Does anyone have any experience with the Audiocodes MP-108 FXO gateway? I'm looking to get one for incoming PSTN lines. In particular, does it pass caller ID information to Asterisk? I currently have a Mediatrix 1204 but Caller ID does not work, even though the specs say it does. All it sends are the names of the ports set up internally on the gateway (ie. "pstnline1" etc) when

Greetings; We are trying to get Asterisk up and happy at our site-we tried VOIP using Sphere about a year ago, spent a *boodle* on expensive hardware and services from a local "expert", but it never was happy. I'm brand-spanking new at VOIP, and I've learned a *ton* getting Asterisk breathing in the last couple of days. I have three Polycom Soundpoint IP 500 SIP phones, which

Is anyone out there using an "AudioCodes MP108 8-Port FXO Analog Gateway (SIP)" with asterisk to support both inbound and outbound calling? If so, I'm interested to hear how it works, and I'd love to see some example confs (both in sip.conf and on the MP108). This product has been recommended to me by a SNOM/Asterisk-friendly distributor, but I would like a second opinion

Hello all, I'm working on a little project right now and have ran into a snag. Was hoping someone would be kind enough to give me a few pointers to help me get past the current issue... I have an AudioCodes MediaPack MP-114 (2FXS and 2FXO... SIP firmware...) that I'm trying to get to play nice with Asterisk 1.4. I've got it to the point where the AudioCodes box picks up

Hello, I'm helping a colleague (*) which has the following setup: ITSP --- <T.38 capable PJSIP trunk> --- Asterisk 13 --- <PJSIP>-- Audiocodes MP-112 --- <FXO/FXS> --- Fax machine My issue is the following : Audiocodes gateway reject INVITEs with 488 Not Acceptable Here It seems this gateway requires t38 settings to be present in SDP body in the very first INVITE. My

I'm having problem passing Caller ID to asterisk from AudioCodes MP-114 (FXO) AudioCodes is passing the caller ID to Asterisk but Asterisk is trying to interpret it as authentication: [Dec 31 11:41:07] WARNING[9752]: chan_sip.c:8553 check_auth: username mismatch, have <pstn-5665>, digest has <pstn-1270> [Dec 31 11:41:07] NOTICE[9752]: chan_sip.c:14316 handle_request_invite:

Jerry and Michael, many many thanks for your posts. Erick. On 5/24/06, The VoIP Connection <asterisk-biz@thevoipconnection.com> wrote: > Here are the step by step instructions for setting up a brand new Audiocodes > FXS gateway for use with an Asterisk server: > > Connect the gateway to a network switch and connect a computer to the same > switch. Then configure the IP