similar to: MGCP Groups

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

I have been told that the combination of call waiting, * and FXO does and will not work because "Asterisk is a PBX". I guess I'd like to hear if this is a hard and fast "no this will not work and here's why", or that this currently doesn't work but with some coding might work. I'd like to have the option to be able to continue using call waiting with an

Hey guys, can you shead some light on this? I will copy my mgcp.conf and post below, but here is the problem. I can't get call waiting to work with my MGCP device. I already have one call going, and I can hear the second call come in, I flash over to it, but all I get is a dial tone, * puts the 1st call on mute/hold, but I never get the second, and it terminates. I flash back over and pick

Hello I have a problem with my MGCP voice gateway. I use D-Link DG104S Boot PROM Version 3.0B38-D Firmware Version 3.0T86-D I tried asterisk v 0.7.2 and I am using latest CVS version now. When I dial a number very fast, or when I use a redial function, my asterisk receives coupled digits. My co-worker called number 245005111, these are a few lines of my debug. The identifier of first digit

Can anyone tell me what MGCP error that I'm getting means? The hardware is a MRP200 in a Cisco 7750 PBX. (Its a FXO blade with 2 slots, first one has a 4 port FXO card and the second has 2 port FXO card. It recognises those correctly, at least to the point of this error.) MGCP Debugging Enabled MGCP read: NTFY 13 aaln/S0/SU0/0@MRP200-S1 MGCP 0.1 X: 1adace42 O: L/hd from

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

I have 1 IP phone (Swissvoice IP10S) and 1 POTS phone. When I dial the number for the IP phone off the POTS phone, the IP phone rings. But when I pick up the handset on the IP phone, I get a busy signal and this message on *: Aug 23 09:38:57 NOTICE[1142106560]: chan_mgcp.c:2243 handle_response: Terminating on result 502 from svip10@00059002042b-1 Here is the entire session. svip10 is the 1 and

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,

I repost a message I put a week ago: I have a Cisco IAD 2431 which has MGCP protocol; I cannot make it to work againts Asterisk; at least there is some MGCP conversation between them but when I offhook a phone attached to IAD I get no tone at all. As anybody managed to get working Asterisk against an MGCP Cisco gateway ? Which MGCP version should I use ? Also I recently

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

Hello everybody! I have an Asterisk 1.2.12.1 server with SIP as the VoIP protocol. What I want to do: I want to talk to the "outside world" via MGCP. I suppose I must set an MGCP peer to route outgoing calls. So, I must set the endpoint syntax of the Asterisk server (Asterisk will act as an MGCP gateway and will talk with an MGCP Gatekeeper) and with other MGCP gateways via

I am trying to dial a mgcp extention from my sip phone and i am getting this error message. anyone got any idea? error I> -- Executing Dial("SIP/2204-5dc2", "MGCP/aaln/1@10.0.1.150") in new stack May 19 22:30:01 NOTICE[1251156800]: chan_mgcp.c:1104 find_subchannel: Gateway '10.0.1.150' (and thus its endpoint 'aaln/1') does not exist May 19 22:30:01

I've never set up an mgcp device before. I have an Adtran IAD with the MGCP firmware on it. I have it configured in mgcp.conf like this: [general] port = 2427 bindaddr = 0.0.0.0 [adtran] host = 192.168.2.2 context = default canreinvite = no line => aaln/1 line => aaln/2 The device is configured like this: MGCP Configuration | Standard MGCP 0.1 / NCS 1.0 MGCP Endpoint

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

Hi: I have a mgcp.conf and a mgcp_additional.conf which records the special information about the extensions. And i found if i use ulaw in the general context in mgcp.conf,then all the registered extensions can make both outbound and inbound calls,the mgcp.conf is following: [general] port = 2727 bindaddr = 0.0.0.0 disallow=all allow=ulaw allow=alaw ; can be disable and do no effect