similar to: IAX protocol will not go through firewall after certain time.

On Sat, 2005-06-18 at 13:17 -0700, Matthew Asham wrote: > For what it's worth I use a residential Shaw connection and have no > problems with IAX registration nor SIP to our Asterisk PBX elsewhere on > the 'net. When I had a dynapic IP connection with shaw, there was not problem either. I just changed to static and IAX can not connect. How can I test it? iax2 show registry Host

I just changed the from DSL to Shaw Cable (static IP) configure the firewall but now asterisk I can not register with FWD nor VoipJet calls going out. I am using IAX with FWD Did I missed to change a setting? I don't think there is any though. I am on shaw extreme connection; I just talked shaw tech. and they are not blocking any port - I was told. So why IAX will not register with FWD and

I find IAX connection with FWD very unreliable so I think I'll have to roll out my own "SIP Express Router" as I want to communicate with few SIP clients. So I hope this the right solution. I'm new to "SER" and to my understanding "SER is like a "road-map" it tells the SIP Clients where they are so they can communicate directly with each other without

I'm just curious why Sipura isn't using free IAX protocol with their devices instead of SIP? With IAX NAT traversal would have been easier, so why are they using SIP. Is there any politics in it? -- #Joseph

Has anybody tried NVFaxDetect Fax detection for sip SIP/IAX channel? There is a new application from Newman Telecom for fax detection. http://www.sineapps.com/news.php?rssid=575 Current Asterisk Fax detection doesn't work for me as I don't have Digium cards; I'm using Siupra -- #Joseph

I have an incoming 800-number over IAX from Teliax and I'm experiencing the large packet loss on connection. When a call comes in there is no ring tone and the first few words of the welcome message are cut off, regardless of the delay I set. Standard call (not 800-number) coming over IAX with the same provider works just fine only the tall free number. So it seems there are some packet loss

Who else makes Analog Telephone Adapters with IAX protocol besides Digium? I've seen Farfon is advertising their unit but I'm not sure if they shipped it or not. Why is so hard for others to support this protocol in their adapters? SIP is totally unsuitable for firewall traversal for security reason. I would like to get min. two port unit. Is it possible to use IAX protocol without

What dtmfmode should I set for IAX protocol? When I dial FWD over IAX it doesn't recognize the numbers I press. -- #Joseph

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

Setup: Office A: router: Linksys WRT54GS running SVEASOFT Alchemy-pre7a v3.37.6.8sv Asterisk: v.1.2.4 static IP Office B: router: Linksys WRT54GL running Linksys firmware v4.30.2 Asterisk: v.1.2.7.1 dynamic IP (using dyndns name) Office A is set up with refresh dns and cron job for iax2 reload every 5 minutes. It rarely looses connection to Office B. Surprisingly, Office B is the one loosing

Asterisk 1.4.21.1 built by asterisk @ lnxca Fedora 7 Well, I did the upgrade from version 1.4.16.2 to 1.4.21.1, activated the qualify for iax users, and Asterisk is still loosing the iax user's registration. Once again this is really wired because no configurations changes have been done to the system, the only change was a reinstallation of asterisk with user "asterisk" instead of

Hi, I've been loosing my mind with NAT and read that IAX doesn't have problems about nat. Does anyone knows about hadware (routers and etc) support IAX? Best regards helder -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20041230/f689bdde/attachment.htm

Hi all, I've searched the wiki, and my basic assumption at this point is to run multiple IAX clients behind NAT I need to specifically code each client to use a different port and then setup that port to be forwarded from the NAT router to their private IP address. At the moment, I can't seem to get more than one IAX client registered behind NAT... am I correct in my above

I have read loads of the emails on the subject but have not read a setup I could use. I have a windows box using Winproxy to dial up the internet through a DSL modem. My internal network I am using while developing. My internet network has been renumbered so that I could test using Nikotel4Mac. It will only accept certain numbering schemes so I have changed my ip's on the internal network

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

Hi Kevin, no you didn't miss the reply and I've not resolved it yet. Have you got similar problems? Pamela Kevin Fjelsted wrote: >Pamela, >Did you resolve the problems you described? >I didn't see a reply on the list but I may have missed it. > >-Kevin > >-----Original Message----- >From: Pamela Weis [mailto:peawy@gmx.at] >Sent: Thursday, August 05, 2004

I'm trying to understand IAX and whether or not it would solve my difficulties: 'The primary goals for IAX were to minimize bandwidth used in media transmissions, with particular attention drawn to control and individual voice calls, and to provide native support for NAT (Network Address Translation) transparency. Another goal is to be easy to use behind firewalls.'

Hello group, I wanted to try out the asterisk iax protocol between two asterisk machines but have several problems with it. My scenario looks like follows. I am using asterisk 0.9.0 on both machines. SER1 <-> asterisk1 <-> IAX <-> asterisk2 <-> SER2 Both SER and asterisk run on a machine with a public IP address. When the telephone on one side makes a call the telephone

Hello all, I am having trouble getting my IAX based Voip provider setup. Any pointers are welcome. So here is the deal. I am registered up and I can make outgoing calls but incoming calls fail. Configs all look good I thought. My PBX is behind our firewall with a direct NAT of one to one for an external IP. IAX port is forwarded UDP and TCP to the internal IP. * shows good registration and

Hi, I have a nufone connection (IAX2), works fine. In my iax.conf I do not specify a time interval that * needs to renew registrations with nufone server. However I can see following registration messages on my cli every 90 seconds (approximately) --Registered to '198.22.67.70', who sees us as 69.5X.XXX.XXX:4569 --Registered to '198.22.67.70', who sees us as 69.5X.XXX.XXX:4569