similar to: Zaptel Disconnect Tone

hi everyone, Is it possible to serially connect my panasonic KX-TD1232 with a Linux box(Asterisk installed) and have it working? -- P. K. kakarizz@fastmail.fm

ðÏÞÅÍÕ ÂÙ É ÎÅÔ? ÷ÏÐÒÏÓ ÔÏÌØËÏ × ÔÏÍ, ËÁË Õ ÔÅÂÑ ÂÕÄÅÔ ÓÏÅÄÉÎÑÔØÓÑ ÐÁÎÁÓÏÎÉË Ó ÁÓÔÅÒÉÓËÏÍ. Date: Wed, 30 Jul 2003 20:06:17 +0400 From: Pavel Zheltouhov <pavlo@comlink.ru> To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] asterisk,ata186 and Panasonic TD1232 Reply-To: asterisk-users@lists.digium.com I have Panasonic TD1232 pbx, few cisco ata186 and linux box with asterisk.

Hi all, There is someone with some experience interconnecting a Panasonic digital PBX (KX-TD1232) with Asterisk? Thank you and best regards, Dan

Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC

Hi. I've searched the archives and found nothing regarding collaborating Asterisk with a Panasonic PBX (TD1232 to be exact) Here's my question: Can I use a Wildcard X100P to connect an outgoing line jack (on the Panasonic) to Asterisk, so I can route calls from the PBX to Asterisk, and calls from Asterisk to the PBX? On the hardware page for the X100P card is says it's great for

Sorry if I post in this forum, this may be not the right one, but I hope to find in here some experts which could help me out. I have in one location 8 extensions from a Panasonic PBX ?KX-TD1232? connected to FXO Ports on an MultiVoIP Gateway from Multitech. On the other location I have 8 SP5100 IP-Phones from Micronet as remote extensions. Between the locations I have a VPN.

Okay, I am facing a move in two months to newly renovated space. I have to decide *this week* between: A) Pull LAN and phone cables, prepare to move and expand our "traditional" PBX (Panasonic KX-TD1232 and VPS200). or B) Pull only LAN cables, go VoIP, use Asterisk as PBX. It is *not* an option to purchase a VoIP system package from Cisco, 3com, etc. Installers are getting an

Thank you for response. So a "standard" quad bri card can serve the KX-TD1232, no need for anyt special fxs similar equipment. Would like not to invest much more money into the Panasonic, I wan't it out :P BR Amund -----Opprinnelig melding----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne av Peter Svensson Sendt: 14. juni

Hello We have around 50 phones in our company, and I am playing with the thought to gradually go over to using sip services and ip-phones internally. However at first I would liked the Asterisk just to sit between the phone line and the Panaosnic, so I can take out one lin/number at a time to use ip phones. I am new to Asterisk, and haven't done much configuring of the PBX either. So I also

If Someone did that, How I connect extensions.conf with this type of Hybrid system to work with asterisk inside this schema: PSTN--->PANASONIC KX <------> Asterisk | |--------->send internal call Thanks.

Anyone have any luck with connecting Asterisk to the Panasonic KX-TD500. I have Asterisk connected via crossover to the TE110P. We are able to make internal calls into the Asterisk Box but the PBX vendor (I know nothing about the KX-TD500) tells us it is not possible route DID over the trunk. I find this hard to believe. Anyone have any luck with this? Thanks! -------------- next part

I have Panasonic TD1232 pbx, few cisco ata186 and linux box with asterisk. Can I dial from asterisk into ata, then indicate phone number playing tone (use DISA feature at panasonic) and connect to any analog phone connected to panasonic ? I think some of Playtones application within Dial application can help me. But I don't know how. -- Pavel Zheltouhov, Comlink ISP, Voronezh, Russia

Hello, We use Asterisk with PAP2 and today we connected the FXS ports of PAP2 to CO ports of our Panasonic KX-TD1232. Problem is that Panasonic doesn't ring - that is doesn't ring every time the PAP2 is ringing. When we reset either Asterisk or the PAP2 it usually rings, but after couple of minutes it stops and only the automatic operator is answering - after 2 rings. We tried changing

Hi, Anybody have an idea how to integrate * with a Panasonic td-1232? We one at the main office, and are installing * in a branch office. We'd like to be able to make calls from * extensions to Panasonic extensions and the other way around. Making outgoing calls from extensions one one side to lines on the other would be nice too. I can put another * machine at the main office, but what is

Hello List, I just started messing with the settings on a SPA-2000, and it has a really nasty alternative dial tone that I want to make go away. I'm not too hip on how the two numbers interact, so my results haven't been good. (I'm in the US, so I'm bias'ed towards US tones.) Default(I'm ok with this one): 350@-19,440@-19;10(*/0/1+2) OutsideLineTone(Bad, really bad. No,

Hey folks, I have a Digium TE205P working as a man in the middle: PRI line -------- Asterisk/TE205P -------- PBX The PBX is a Panasonic KX - TVP 100. Everything is working great except for one little issue. Asterisk isn't hanging up the PRI B channel when the PBX channel is hung up. I don't want to overload you with information but please ask if more is needed. I suspect I'm

Roberto Could you provide more details about Panasonic PBX test? model unit and configuration details? Best regards Mc GRATH Ricardo E-Mail mcgrathr at mail2web.com

Roberto Thanks. Panasonic KX-TD1232 system ISDN interface use DDK plug, not same cord you are using for openvox B400P card. Each port could be configured as CO or extension port as Point-Point or PTMP in both mode. Regarding to dial timeout these it becomes from ISDN dial mode overlap or En-bloc, by the way you can close dialling number by using # key. Best regards Mc GRATH Ricardo E-Mail

I have an Asterisk system running on T1 PRI trunks using a TE405P. It seems to be running ok, but one thing puzzles me. Every so often I get a raft of messages like this: -- B-channel 0/1 successfully restarted on span 1 -- B-channel 0/2 successfully restarted on span 1 ....... -- B-channel 0/22 successfully restarted on span 1 -- B-channel 0/23 successfully restarted on span 1 I could

Hi all, I would be most grateful if someone would review my plans for my new phone system and comment on areas of expected trouble and advice on what to do better. Instead of moving our Panasonic KX-TD1232/TVS200 system (ugh...) to our new location, we've decided to jump into IP telephony with *. But we are new to * (but not Linux), so we're trying to learn as much as we can before we