similar to: No ringing tone on outgoing SIP trunk

Hi, We are using VOIP-SIP gateway to route outbound PSTN calls. Recently, I am getting == No one is available to answer at this time message, after making 5 SIP attempts (Retransmitting #5 (no NAT):), and the calls are going out through alternate Zap-trunk. I do not see any hit (sip-debug traffic) on the voip-gateway for the failed calls. Strange thing is that this is happening randomly,

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Hello, I have a TDM400 and currently have 2 of the ZAP Trunks configured on it. Zap/1-1 and Zap/2-1. I am Running Asterisk@home Version 2.4 with AMP version 1.10.010 In my Outbound Routing I have the Trunk Sequence set up so that 0 is Zap/1-1 and 1 is ZAP/2-1 What I see is that when Trunk Sequence 0 is full, it does not open Trunk Sequence 1. I have found that this is true even if I

I setup my aah box with a sip trunk at irisxa.iristel.net Incaming it is ok but when I try to dial 8 and the nr where I want to call I get all line is busy. In my log I have these: Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:04 DEBUG[3156] manager.c: Manager received command 'Command' Feb 22 14:33:19 VERBOSE[2721] logger.c: --

Hi - I've recently bought a mediatrix 1204 and have had a complete nightmare getting it up and running with an asterisk@home setup. I know this isn't a mediatrix list but I'm at my wits end and the support with this product is atrocious. (mine was even shipped with firmware that was incompatible with the win32 software it came with so I wasted a day trying to work out why the SNMP

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I have a Asterisk @home ver 1.0 running with a TDMB11 card. Several sip extensions and a regular phone connected to the box. All routing works fine from the regular phone connected to the box, whether its going to FWD, broadvoice or the PSTN. The problem I am experiencing comes from making calls from the sip phones. They get routed correctly to the sip and iax trunks but when making calls

Hi Guys, I'm having sound problems when diverting a call using asterisk@home 1.5. I am using the following configuration in extensions_custom.conf, extensions_additional.conf and extensions.conf [custom-Sales] exten => s,1,SetVar(DivertNumber=02XXXXXXXX) exten => s,2,Dial(SIP/116, 15) exten => s,3,Goto(outrt-010-outside3,9${DivertNumber},1) (i have replaced the diverted phone

Apologies if this has already been posted to the list. I sent it about an hour ago and it hasn't shown up yet. I've changed the format to plain text in case that was the issue. I'm having a major issue whereby voice is going out fine but none is coming in. If I ring someone I will hear them answer and then nothing. They still can hear me. Looked at the logs and with my

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hello, I have *@Home 1.5 installed and all is working fine for incoming calls and sometimes outgoing calls. Installed in the box is a digium TDM04B (4xFXO Ports) setup as ZAP1 to ZAP4. I have incoming calls coming in on lines 1-4 in that order and outgoing calls prefering ZAP4 then ZAP3 then ZAP2. When i try to dial out to the PSTN from a SIP phone it sometimes works (normally after a reboot)

I am posting this in case someone need help.. ========================================================= YOU THA MAN!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! No sure how I will repay you, but anything you need, just let me know!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Thank you, thank you, thank you!!!!!!!! -- Executing GotoIf("SIP/2007-12c7", "0?4") in new stack

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

Hi all, I've recentrly starting to play around with *, when all I wanted is to configure an fritz ISDN card with A@H. Currently I'm stuck at the phase of what do I do with capi after everything is installed. I'm trying to understand how to setup incoming and outgoing calls at A@H since I'm getting a bit lost with the default dial plan. It seems that * answers but disconnect

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as