similar to: RJ45 instead RJ11 in Digium's TDM20B card help meplease

Dear all, I am happy to tell you that I received a Digium's TDM20B card for my Asterisk box today. but the phone jack is RJ45 instead of RJ11. So Please I need precise instructions to connect a phone to this card. please, assume that I have a phone (a normal analouge phone connected to the one end of a cable with an RJ11 jack (at the phone side). and now I want to connect the other end to the

>what is the wire combination/sequence >for a successful installation? http://www.google.ca/search?hl=en&c2coff=1&q=rj-11+rj-45+site%3Alists.digium .com&meta= hth

<div><BR>Hello,</div> <div>&nbsp;I bought a TDM400P, and intended to use it with my analog phone, which is RJ11 ofcourse. So, the question now, how do I plug in my RJ11 phone to the TDM400P card, which has an RJ45 interface? Also, since it's an 11B card, I also intend to bring in an analog line into the RJ45, so i am still left with the same question....how do I go

Sauda??es. Como que se faz um conector RJ45 em uma ponta e RJ11 e outra. Pretendo conectar a linha de um ATA em uma placa Khomp KFXO IP. A ponta que tem o conector RJ45 est? crimpada com a sequencia 568B e vai ser conectada na placa Khomp, mas a ponta RJ11 eu n?o sei como deve ficar. Li alguns manuais na internet mas n?o entendi ao certo como tem que ser feito. -- Att.* *** Luis H. Forchesatto

Hi all, I am going to have a TDM20B FXS card and sit in it in my Asterisk box, I need out going calls only. I am quite a newbei of it, I hope your tips and tricks with valuable links. Thank you Kumara

Hi all, again, with another question ( may be the final one) I have come up to this point, means when I dial a number in my analogue (panasonic) phone I hear the ring at the end through my asterisk box (via TDM20B card) that uses IAX2 over teliax and after time-out, it gives this message. Starting simple switch on 'Zap/1-1' -- Executing

Hi all, Does anyone run Asterisk on FC4? with Digium's TDM40B cards. any success stories? my Intel 865 M'd+ Intel 3.0GHz freezee during installation (FC4). Please any comments? Kumara

Morning, I've installed asterisk on FC4 and had a few problems with zaptel stuff. Having installed it on SuSE I was able to check a few things that were different. When installed with the RPMS, the udev stuff gets put into the normal 50-udev file under /etc/udev. On SuSE, it worked when the necessary zaptel section was in a separate file name 55-zaptel.udev (the name is arbitrary,

Hi all, I have a vergin Linux box (FC3) and Digium's TDM20B card installed in it. I followed the Digium's quick intallation guide. donwloded CVS successfully, installed in this order zaptel>libpri>Asterisk and got this error without installing asterisk in my box. ***************************************************** (this is the end of the screen dump) /usr/bin/ld: cannot find -lidn

I have a TDM20B and asterisk compiled fine. The drivers have been loaded (wcfxs and run ztcfg -vv, I see the drivers loaded with lsmod). Asterisk starts up fine. I am using the default configuration files that are made when you do a "make samples". I was wondering if someone had a link or website that stepped someone through this kind of setup. What I want to do right now, is use a

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

Hi All, I am very happy to say that after solving a lot of problems I got my Asterisk box talking (with a Digium's TDM20B card) last 48hrs I was sending message to many people asking help. I found some solutions myself but the base of those solutions given by the generous people in the list. I appriciate all of them once again. Now, I have minor problems like jitter and fine-tuning, I am going

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

Hi All, I have this codec problem, I use "gsm" in my iax.conf file and in teliax settings also, but the error is still appearing as below. please help me. Kumara Starting simple switch on 'Zap/1-1' -- Executing Dial("Zap/1-1","IAX2/kumara@teliax/01194777070239|30|tr") in new stack -- Called kumara@teliax/01194777070239 -- Call accepted by

Hi, I'm trying to use a Detewe TA 33-clip but there is no rj11 connector on it...only a TAE connector. I'd like to create an adapter so I need to know which TAE pins to connect to RJ 11 pins. Is there anybody who knows where I can find a schema of that adapter? Single connector pinout may help too. TIA Giorgio Incantalupo

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

Greeting!, I read somewhere that without cdr, Mysql etc it is possible to take outgoing-call-logs to a text file. (I am not sure please). is it really possible ? if so, how do I do it? any links to refer? Thank you. Kumara

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

Does the voicetronix card work with Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of woody+asterisk@solutionsfirst.com.au Sent: Monday, February 02, 2004 11:06 PM To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Pictures of new multiport FXO/FXS from digum > -----Original Message-----

I have some IP 500s that I bought used, but the connectors are different than the new ones. There is a Modem/Power RJ11, a Line RJ11, and Handset and headset connector. Does anyone know how they work? -- Chris Mason NetConcepts (264) 497-5670 Fax: (264) 497-8463 Int: (305) 704-7249 Fax: (815)301-9759 Cell: 264-235-5670 Yahoo IM: netconcepts_anguilla@yahoo.com