similar to: HT-488 vs. SPA-3000?

Anyone tried to muck around with using the 488 for both fxs and fxo with asterisk? I've been playing with one for the last couple of days, and it looks like its a little lower quality then the spa3k. No gain settings, echo canceller is less then ideal on long analog pstn loops, etc. Anyone with good experiences?

OK, I've spent way more time than I wanted to on getting an x100p clone to work in Australia. I'm happy to consider other (more functional) options. Does anyone have an opinion on both the Sipura 3000 and other Digium cards (like the TDM400P)? I need something that works with no much fuzz. I know the Sipura 3000 is cheaper the the TDM400P card. All I need is to channel my POTS line

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

This is a wierd one. Can't figure it out. I have an SPA-3000 at the house handling my incoming line. It's setup to direct the incoming call to asterisk. Works great 99% of the time. A few times a day, I'm getting calls that ring once internally and are then hungup. I managed to get a detailed log [1] of what's happening today and it looks to me that the SPA is acting wierd.

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

Hello all, I have an ISDN termination box (TR1) that converts ISDN(Bri) to 2 normal analogue lines. The same number is assigned to these lines. These lines are connected to 2 spa3k registered to my asterisk box. When calls arrive, TR1 try to pass call to the first spa. If spa not takes the call immediately then try to pass to the other spa. The only configuration I found works is to put the

I'm experiencing a very unusual problem with a few of my sipuras. They keep over heating after minimal usage. I unplug them and let them sit for 15 minutes and it starts working fine. The other way around is that I put a fan on it or something to keep it cooling. Has anyone else experienced this or are they just defective units? Regards, Mohammed Salim EZZI Telecom, Inc.

Hi, i have a HT 488 and I want using this like an FXO for Asterisk. I have find some configuration in the list archive & google but my HT with these config not work. my sip.conf [HT-488] username=400 type=peer secret=wowowow qualify=yes port=5062 nat=no host=192.168.1.157 fromuser=400 disallow=all context=from-pstn allow=g711u allow=ulaw allow=alaw my sip debug:

Hello All, I am trying to figure out which way to go for a quad port fxo solution with a good echo can on it. My options are the sangoma remora, a mediatrix fxo, or something similar. The issue is that I would need a good EC. This would be on about a 9000 foot loop, and the lines don't function well on a spa-3000 or zaptel tdm 4 port card. Anyone have experience that drives them in a

Anybody using a Sipura 3000 for FXO with Asterisk? Mine is working except for one small nit... When a call comes in from the PSTN, the Sipura answers it and then passes it on to Asterisk, which plays extension ring tone. I'd prefer for the POTS line to stay on-hook while the extension rings, and to only be answered by the Sipura when the extension answers. Has anybody made this work?

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

Hello. Has anyone run into problems accessing voicemail with the Sipura SPA-2002's? Our SPA-2000's work fine (registers fine, able to make and receive calls properly & also able to access voicemail). We've configured the 2002's exactly the same way. However, with the SPA-2002 we're unable to access the voicemail system (though it does register fine and is able to

Ok, I am back from my thanksgiving holiday, and I find there was a big snow storm here in Seattle. Apparently during the storm there where multiple brown out/black outs. I have struggled since day one to get a high quality PSTN gateway configured with my very long loop and Mac based asterisk. I originally tried the HT-488, which had multiple issues, and was unacceptable. I then purchased

First of all, I'm not knocking Sipura/Linksys. I have heard very good things about their products. I'm just wondering if they are the only quality shop on the market. I know about the zoom 5801 where you can't dial out the FXO from SIP, only from the FXS port. And I have heard similar about the HT-488 also. I want to know if anyone else makes ATAs where all of the features work

Hi All, I have a GSM box, which needs to connect to a analogue phone line. I've plugged the GSM box to a Grandstream ATA (386). This ATA has extension number 600. Now what I want to accomplish is the following: - If a mobile-number is chosen by a user, asterisk needs to call the ATA (600), wait for a few seconds, and then send the mobile-phonenumber. Or, if it's possible, define the

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

Anyone know of any equipment that I can use to connect a laptop running asterisk to a POTS line (RJ11) ? Regards, Dovid __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com