similar to: Asterisk and Alcatel 4200 PBX

Is features.conf included in the cvs as of 8-1-04? I have updated, but am not seeing it?

Hi, Does anyone have any experience connecting asterisk to alcatel 4200 series pbx with bri cards? Does it should work with asterisk bri in NT mode, and alcatel bri with TE mode? Cheers, Igor Neves.

Hello, I have connected asterisk box with legacy PBX Alcatel OmniPCX 4400 (and also another * box connected to A4200). These PBXes have function to assign name to extensions and display it on phone. Asterisk box is connected via PRI with euroISDN signalling (also I have tried QSIG). Is it possible to set callerid with name and display it on alcatel digital phones? With command SetCALLERID

Hi, I have two tables and I need to merge both. I use the merge command, but in this way the name must be exactly. How I can make to compare independently of upper or lower-case? Look: data1<-data.frame(journal=c("Ecology","Environmental Entomology","Neotropical Biology And Conservation"))

Hi, I followed the how-to from http://www.alcatelunleashed.com/viewtopic.php?f=44&t=840 All works fine except for Asterisk->Alcatel calls. Actually, calls from Asterisk to analog extensions on the Alcatel work. However, calls from Aserisk to digital extensions on the Alcatel 4400 do NOT work. I get this error in the Asterisk log: -- Executing Dial("SIP/4053-0823dd48",

Hello, For a prospective customer, I need to evaluate the cost of an Alcatel OXE IP trunking licence price. The setup would be: PSTN -----<E1>---- Alcatel ----<SIP>----Asterisk ---------- SIP Phones At the moment, only a couple of simultaneous calls are needed between Alcatel PBX and Asterisk but later, this number will grow.

Hi guys, I need to interconnect an asterisk server (1.4.17) with an alcatel pbx, because i want that an asterisk extension can call an alcatel extension and viceversa. I need to do this throug a NT port (of the digium card) for technical reasons (linked with alcatel hardware). Card installation was fine, but i'm not sure of the configuration i choose. In /etc/misdn-init.conf i put my

Hello everybody I have an asterisk with an integration of alcatel pbx, by sip trunk, all calls are fine, but tha calls calls that originate from a analog line, the recipient is not listening, and that if they hear the call originates, the lines are E1 in alcatel pbx. When a asteris user call to analog line the call is ok. Everyone, has been that problem? I change asterisk version 1.4.21 to

Hi I just came accross this Newbridge Mainstreet 3624 but the Alctel site appears to have zip for reference/user manuals Anyone by chance have 1 of these or a url for the docs ? thx

Does anybody has experience with the SIP phone of Alcatel the ST280. I can't make a call with this phone. Everytime I make a call I get the error Jun 12 19:38:38 WARNING[1133718080]: chan_sip.c:497 retrans_pkt: Maximum retries exceeded on call 5624@81.124.191.47 for seqno 1 (Response)

Hi there! I wan't to connect my * to an Alcatel 4400. Does anybody have some experiences with that? I have the problem that I can dial in to *, but not *->A4400 . :-( Thx Marc

Hello, I have the following problem with HFC card and Alcatel PBX 4400: - I want to connect Alcatel PBX and Asterisk with HFC card (zaphfc driver 1port S0/T0 interface card) - BRI line is configured at PBX to T0 trunk - In asterisk I have loaded zahfc driver in NT mode and also set in zapata.conf NT mode, point-to-multipoint. - I am using cross "isdn" cable to PBX -

Greetings list, I've been asked by someone to help them set up a SIP link between an asterisk system and an Alcatel OmniPCX (v6 software). The asterisk bit's fine, but I know nothing about the Alcatel except that it does apparently allow the setup of SIP trunks. Does anyone have experience with the Alcatel unit? Any obvious pitfalls to watch out for? Any suggestions gratefully

Hi, I'm sorry if this is already asked somewhere on the list but I couldn't find it. We have an old PBX system controlled by our Telecom provider. There are analog phones but also digital alcatel phone's connected to it. These are not ip based but legacy digital phone's. Is there a way how we can connect them to our own Asterisk PBX? The old PBX is going to be removed, so it has

Hello everybody, I just buy a X101p clone and i'm new in asterisk. Here is my configuration : ISDN line ---- Alcatel ----PSTN ext 68-----Asterisk with X101p clone ------sip phone ext 200 - 203 ||| ISDN phones ext 60-67 >From sip phone to ext 60-67 it works. 9+extnumber >From sip phone to Land lines it works. 9+0+phone number >From ext

Hi all! Is anyone using the $subject setup? What I would like to do the following setup: 1. OXE is setup for receiving calls, handling Agents 2. Asterisk as external IVR on extension 9xxx connected with ISDN (Q.931) PRI The incoming calling route: 1. OXE handles incoming calls, answer 2. Transfer to extension 9xxx 3. Asterisk answer (using one channel) 4. IVR is handling calls 5. If needed IVR

Hello, Since upgrading from asterisk 11 to asterisk 13 (I have tested up to the latest 13.16.0 release), we have a problem with attended transfers to an alcatel pbx in which the call being transferred still has music on hold even after the transfer has completed. Is this a known issue? Any new flags that need setting, etc? Thanks Jason -------------- next part -------------- An HTML attachment

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

Hi guys, I have an Alcatel 4200 with a ISDN board pluged in the asterisk server with TE110P. Input calls VOIP Proider ---> Asterisk ---> Alcatel Output Calls VOIP Proider <--- Asterisk <--- Alcatel In alcatel phones, users should dial 2 for take a line tone and can dial. At this point start my problems: 1. When users dial 2 on phone (alcatel) they don't received a dial tone,

Does anyone have any input into integrating asterisk with a alcatel 4400 PBX. Acording to what i've found is that Alcatel uses R2 for E1 -- regards Vikram (http://www.vicramresearch.com)