similar to: Fax + Fritz + Capi + detection

Hello, I have problem with capi, I can't install it. I have putted all info what I did and what I get :). I think you can suggest me how to solve this problem.and thanking you in anticipation. I have ISDN Frtiz!Card PCI v2.1and I want to install it to my ubuntu box (kernel: 2.6.17-10-server). Using command "lspci -vv" , I can see that kernel finds this card: *02:0d.0 Network

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hello all, I just got the latest cvs snapshot and I'm trying to compile asterisk.. When I run nefeli:/usr/src/asterisk/zaptel# make clean; make linux26 Compile stops with errors... /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 2 of 'class_device_create' makes pointer from integer without a cast /usr/src/asterisk/zaptel/zaptel.c:6509: warning: passing argument 3

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

Hi, Since Carl has kindly provided us with fax support for CAPI based cards, we have been using it with much success. Today I have modified app_capiFax so that it now supports a dynamic CSID. The following example uses the DNID created by chan_capi on an AVM Fritz! card. * Receive a fax with CAPI API. * Usage : capiAnswerFax2(path_output_file.SFF|stationID) * * This function can be

I've put my fire proof suit on ready to ask a question ;o) Redhat 9 Kernel 2.4.20-8 AVM Fritz PCI Problem 1... i have followed instructions from:- http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI (Plus many many other sites found via google over the last 16 hours) after modifying the makefile & defs.h,

Hello, I have been wrestling with installing the CAPI drivers for AVM Fritz in order to use chan_capi with Asterisk. I use an SMP machine, RH 9. I have found rpm's for CAPI and AVM drivers (namely: capi4k-utils-2003.06.16-08.mungo.RH9.i686.rpm and kernel-2.4.20-8- avmfcpci-03.11.02-08.mungo.RH9.i686.rpm), but I believe that they support only single processor machines. I've already

Hi All, Has anyone had success with using the AVM Fritz PCI ISDN Card (v2) CAPI drivers with a distro other than suse? The AVM driver is geared towards suse, and after trying them with RedHat 9 I've not got very far. The module compiles but dies when I attempt to modprobe it. I've googled until I almost lost the will to live! What little information I can find seems to refer back to

I have an Asterisk box running happily under Fedora Core 2 with a X100P and a TDM400P, and now I'd like to integrate it to my ISDN2e connection using either an AVM Fritz PCI card or an Eicon DIVA passive card, both of which I have sculling around. I've successfully used the AVM card under RedHat 8.0, but I'm having difficulty finding information on running it under the Fedora 2.6

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

Hi All, I'm running asterisk 1.0.7 on debian sarge, and hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.5. The problem is that any inbound/outbound calls on analogue line result in echo on MY end (the asterisk end). I've played with the echo settings in capi.conf (mainly turning on echocancel and echosquelch, also tried playing with rxgain/txgain) to no avail. The only

HI all, Has anyone succesfully installed an AVM Fritz! card on Fedora 7 using the drivers at ATrpms recently? http://atrpms.net/dist/f7/fcpci/ I tried with a clean F7 build on my EPIA 5000 yesterday, after modifying /etc/capi.conf (removing the coment # in front of fcpci line) I received the following error when executing 'capiinit' - FATAL: Error inserting fcpci

Hello all, I would like to know about the support for this ISDN passive card AVM Fritz-PCI v2.0 with Asterisk: 1. which drive should I use with Asterisk: isdn4linux or capi4linux from AVM (I read some messages on the asterisk-users archives but I didn't find the answer) 2. if the drive is isdn4linux then HiSAX support (for passive cards) is enough ? and the device /dev/ttyI0 (for

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN