similar to: Service Unavailble, Sipura 3000, CheckGroup, what the heck??

I'm experiencing a very unusual problem with a few of my sipuras. They keep over heating after minimal usage. I unplug them and let them sit for 15 minutes and it starts working fine. The other way around is that I put a fan on it or something to keep it cooling. Has anyone else experienced this or are they just defective units? Regards, Mohammed Salim EZZI Telecom, Inc.

Can anybody show me a working Sipura 3000 setup please? I need to setup one to my * box, ... What are the variants you can setup? Advantage - disadvantage. bye Ronald Wiplinger

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

My SIP phones can dial out through Sipura SPA3k to POTS for local and 911 calls _but_ incoming POTS calls are being swallowup somehow. Am I on the right track with the code snippit below? sip.conf: --------- In sip.conf the following code is _supposed_ to ring the SIP phones when a POTS line call comes in through Sipuara to Asterisk. [spa3k-pstn-in] ; Pots-line-in from Sipura ; If

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

First of all, I'm not knocking Sipura/Linksys. I have heard very good things about their products. I'm just wondering if they are the only quality shop on the market. I know about the zoom 5801 where you can't dial out the FXO from SIP, only from the FXS port. And I have heard similar about the HT-488 also. I want to know if anyone else makes ATAs where all of the features work

I am checking on the SetGroup / CheckGroup commands, but I have some troubles to undestand the examples. SetGroup(moh) can be moh anything as I like? Usually moh stands for "music on hold" CheckGroup(1) checks if somebody in in group "moh". Does it mean I can only have one SetGroup(xxx) ?? When I look at example 2 than I see two SetGroup commands and one CheckGroup

I'm running multiple asterisk servers and need to use the CheckGroup function (and other group functions) across multiple servers Ex: - there are 5 channels in group test on server 1 - there are 8 channels in group test on server 2 I would need a checkgroup to return me 13. Any way to currently do this ? What would be the best way to implement this if not ? Store group setting in shared

I have a rather long dial plan, but it includes support for call waiting. However, the setgroup checkgroup commands don't seem to be working. Can anyone help on this one? Excerpts are below. First exten-vm is dialed and then dial-new. As I understand, priority 1 increments the active channels for the caller and then in "dial-new" priority 8 increments for Arg3, or the Callee

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

How can I dial *67 on a Sipura 3000 if I dial from a SIP phone connected on an asterisk server. I always get a message saying that authentication failed for INVITE for sip221@192.168.1.6. If I dial a number without doing *67 it's working fine... sip 221 being the extension of my Cisco phone and 192.168.1.6 being the IP of my asterisk server... I have my outgoing context configure

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not

Hi there, I was wondering how I can use setgroup and checkgroup for perfom incoming and outgoing limitation checks. I've have some users that doesn't what to be able to recieve more than 1 call at a time, and I also want to limit a users outgoing call abilities. Any help would be greatly appreciated. Kind regards Cf --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus

Does anyone know if SetGroup and CheckGroup apply to only current context or is it per server based? Ta SJ

>From this list I found that I could use SetGroup and CheckGroup to do what I wanted. But I'm not quite sure how I do it. The case is that I have 3 user groups, and one main group. The main group is for all the incoming calls from external phones. The main group should be allowed to have 3 calls at the time. The 3 user groups are internal groups that I want to limit by ony having one

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA

Arrggghh. Tearing my hair out here. I'm trying to set up the spa3000 in the UK for my home, and want * to control the dial plan I've googled to no avail. I've read the manual to no avail. Can someone, please let me know what the parameters is the spa and * are to a) receive a call from the pstn b) make a call to the pstn from the phone attached I can make sip to sip calls (i.e. I

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

I need to place a call using a "pin code". To access an external line, the host PBX (a Ericsson MD-110) will require that I dial *72*pincode#phone_number to complete any (trunk) call. When I send the number, my Sipura 3000 will reject the call with "Forbidden - wrong password on authentication for INVITE" (see below). All other calls sent to the Sipura box without the