similar to: Unreliable DTMF detection with DISA on incoming Zap channel on bristuffed * and GSM gateway

Hi, I'm getting unreliable dtmf recognition (it works fine for 4-5 digits, errors (duplicates) on more), when transferred inband from gsm gateway to NT port of quadbri under bristuffed Asterisk..... Since Asterisk is claimed to have good dtmf recognizer, I suspect there are some settings to workarouned... I've tried dtmf relax, but didn't help, so I suspect gain settings.... Is

Hi, I am currently building a 1.4.4 Asterisk box for a client and they are interested in GSM functionality. Does anyone have any experience with a GSM card, preferably Quad Span (4 GSM modules or higher) for use in the UK. I have seen the Junghanns* version but I am not keen on the limitation of having to use a BriStuffed version of Asterisk. Do Digium make one ? as I am unable to find

Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and

Hi! Asterisk in Debian/Lenny claims to be bristuffed, not? At least the the Debian patch tracking system shows the bristuff-patches: [1] http://bit.ly/bRRHe7 We have a QuadBRI-Card and recently needed support from Junghanns.net but they refused telling us there is no bristuff installed because of the show version output: *CLI> show version Asterisk 1.4.21.2~dfsg-3+lenny1 built by pbuilder @

Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi, I'm using spandsp-0.0.3 [http://www.soft-switch.org/downloads/snapshots/spandsp/ spandsp-20061116.tar.gz] on a bristuffed asterisk (1.2.13) [http://212.91.251.199/~junghanns.net/downloads/bristuff-0.3.0- PRE-1v.tar.gz] libtiff is at version 3.6.0 Running on: Linux router2 2.6.17-2-686 #1 SMP Wed Sep 13 16:34:10 UTC 2006 i686 GNU/Linux Debian testing distro. I've tried many

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

I have a serious problem that repeats very often, after 30 - 50 calls and I can only solve it by stopped and restarting * :-( After a while, * seems to loose track of something. When an ISDN call from PBX needs to go to the Telco, I get 'Ring requested on unconfigured channel 255/255 span 2' It's always channel 255/255 ??, the 'span' number is random Setup: * between Local

Hi all, I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns QuadBRI running in NT-mode. Connected to the BRI-Ports are 12 Fax-Modems (Elsa MicroLink ISDN/TL V.34) which are only operating in dial out analog mode to deliver fax messages. After a while of running fine (50-200 dial out connections) on some S0 spans the following message occurs

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Ok, I usually use the latest stable CVS, with no patches or modifications. If figured if there was a worthwhile patch, Mark would have already included it. However, there was that neat patch about being able to press a certain key and it'd begin recording in mid-stream, that was an awesome feature and I patched my latest features.c file with that patch. But I keep seeing mentions of other

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

I'm using Asterisk 1.0.2-BRIstuffed-0.2.0-RC2b - when anyone picks up a call with '*8' - the call will drop after about 20 or so seconds. Is this a general problem with Asterisk 1.0.2? As this is the latest release that it appears Klaus-Peter Junghanns has for public consumption - is there anything I can patch for just this problem - or has Klaus-Peter Junghanns (or anyone else) been

Hi all, My BRIstuffed 0.2.0-RC7k is running fine on my debian box for voice calls over ISDN2. Now I want to implement receiving incoming faxes into my setup so I did a google and some reading on the wiki. I got the spandsp 0.0.2pre10 package compiled and installed, patched asterisk's apps makefile and compiled * again. This all worked out fine. When integrating the RxFax into my dialplan the

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hi, I'd like to use DISA properly for my case - I'd like to handle it right, if user when in DISA doesn't dial any number - how does Asterisk return from DISA cmd ? I'd like to dial some default number if user doesn't dial anything or give him some message - but I don't know what gets executed after DISA if nothing is dialed .... I'm reading this on wiki, but

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

I tried to get callerid working the normal way but the cid is never passed to the phone. It doesn't work untill I set SetCIDNum(0${PRI_NETWORK_CID}) in extensions.conf which I found in the wiki: http://www.voip-info.org/tiki-print.php?page=Asterisk+zaphfc Is this intended behaviour, or still a bug? It does work but it only shows one zero even though I have nationalprefix = 0

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...