similar to: High CPU in Asterisk, chan_unicall and dtmf

Hi, I have successfully installed libunicall and mfcr2 in Venezuelan variant. We are able to receive, make calls without any problems. When we place a call from a snom sip phone through chan_unicall and press a dtmf (either using info, rfc2833 or inband) Asterisk seems to get the order of playing dtmf but a garbage is heard at the other side. I have been trying to narrow down the problem on

I have a problem with inbound and outbound calls in asterisk. I read previous thread, and then test new versions of unicall, but I don't have success, the problem persist. The system suffers CPU peeks with a single conversation, with an interval of 5 or 10 seconds. My system has: asterisk 1.0.5 zaptel 1.0.4 libunicall 0.0.3-pre3 hardware: E100P Also, I made traces with strace, but all

Hi Kaws, I may need to add some notes; 1. The default .rpm version of libtiff in RH9 does not seem to contain some functional entries required for libunicall / libmfcr2. Therefore when compiling libunicall "unresolved references....." will happen. To solve this, I needed to recompile libtiff from the tarball. When installing libtiff, the default directories will be under

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall libmfcr2-0.0.3 is

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia (north africa). I have configure my MFCR2 according argentina R2 settigs : the test call run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2. generally in the begging no errors occur. after

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I

If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hello again :-( I have a problem with chan_unicall. If I have two simultaneous incoming or outgoing calls, they sound broken because cpu load goes to 99%. Also with one call, the cpu load goes to 99%. Seems like device /dev/zap/channel is busy after 5 or 10 seconds , and chan_unicall does not write to this. strace with asterisk-1.0.7, zaptel-1.0.7, kernel-2.6.10 ================================

hi all, this message is destinate to users who rub libunicall on asterisk succefuly ... my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is as follows: with version FC3 I have success to run libunicall without problem, the testcall run perfectly well. askterisk run without problem on the

On 8/23/07, sanchal.singh at alliance-infotech.com Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2

I am in the middle of installing chan_unicall.c and channels_Makefile.patch in my channels directory as instructed at the bottom of this doc/site: http://soft-switch.org/unicall/installing-mfcr2.html. I am at lost 'coz I don't know where is my channel directory is 'til someone told me that it is where all my chan_xx.so resides, so I copied them to this directory. Next, I have to issue

---------- Forwarded message ---------- From: Brian Hutchinson <b.hutchman at gmail.com> Date: Fri, 11 Jan 2008 12:22:09 -0500 Subject: Trying to build MFC/R2 Hi Moy, I downloaded your astunical-1.4.16 and have been studying it. I have a machine running the latest download of asterisk-1.4-17 and was trying to figure out how to build MFC/R2 support into it. I merged your unicall specific

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I

Dial(UniCall/g1|300|) Where is the number you want to reach? I'd expect to see Dial(Unicall/g1/1234567890|300) To reach number 1234567890 - Mois=E9s Silva On Jan 30, 2008 1:21 PM, Roger C. Beraldi Martins <rogerberaldi at gmail.com> wrote: > Dears, > > After weeks trying to contact support of my telecom about 'Seize Ack' > because that is not returned, was a