similar to: pridialplan & prilocaldialplan

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

hi. could somebody explain how exactly the following parameters in zapata.conf work: pridialplan prilocaldialplan internationalprefix nationalprefix localprefix privateprefix unknownprefix the wiki & comments doesn't quite explain them. and phone companies are absolutely no help. i've setup systems in the US & China with trial & error until it works. now i'm setting up a

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

Hi all, I've been batting my head against a brick wall for the best part of the day and still haven't got any further (apart from getting a big headache, that is). I've searched the Wiki and Googled the hours away, but I still can't find supportive documentation. I've just replaced my ISDN Fritz!/chan_capi setup with a HFC/Zap configuration and had the following problems: 1

hi folks. does any one have experience setting up E1 PRI in Shanghai, China? it works fine when we use SIP phone to dial out, however when using forward function on the same phone, it seems like it's dialing out but there's actually no respond from the phone company (China Telecom) and eventually the dial command will timed out. here's our PRI portion of zapata.conf:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, Can someone explain what the parameters pridialplan and prilocaldialplan are? What do they do and do I need them? I've connected an asterisk box via E1 (sangoma) to an alcatel 4200 pbx. The pbx technican complains about the format of the nr asterisk sends. Asterisk sends all numbers in on piece the pbx expects the numbers devided into

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

After setting the pridialplan=unknown I seeing the Called Number TON change to Unknown Number Type but not the Calling Number TON. Should both be following this parameter or not. If not is their another option to change the Calling Number TON? > Progress Indicator (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) 0: 0 Location: User (0) > Ext: 1 Progress

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi, I have two HFC-s boards I configured in NT and TE mode respectively. When I connect the two boards together, I can dial extensions and I see the correct called and caller ID numbers: -- Executing SetCallerID("Zap/2-1", "7516862") in new stack == CDR updated on Zap/2-1 -- Executing Dial("Zap/2-1", "Zap/g2/0795025602|30|r") in new stack --

Hi I'm beginner in list. I have doubts about the options pridialplan and prilocaldiaplan in chan_dahdi.conf. I interconnect the Asterisk with a Siemens PBX, but i saw that the changes in the file do not take effect in debug of the span or calling/called number. How to use this options? In that cases to use? Ps.: sorry for the english, i'm brazilian. Thanks -- Att, Rafael Saraiva

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hello, I have an Asterisk system in the UK using ISDN service from BT. My problem is that the called number is always passed to the provider with the Type Of Number declared as ?national? despite pridialplan (and prilocaldialplan) is set to ?unknown?. My questions are: - How can I find out what the effective value is for the above two variables without actually making a call? (I have very

Hi all, I have Asterisk working great for a while now, and until now, only needed to forward calls which originate from one country (Holland, +31). We have a Wildcard TE410P card and configured it in zapata.conf as: switchtype: euroisdn pridialplan: unknown ...etc This was all fine, but now we want to also forward calls to the voice-switch with a calling-number with a different country code.

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

My international calls are not connecting. [general] pridialplan=dynamic ;prilocaldialplan=unknown internationalprefix=00 nationalprefix=0 localprefix= I have the above in my zapta.conf - yet when I dial an international number, I get a ring, then I get the message "the person you are calling, is currently unavailable" This is an ubuntu machine, with a sangoma card, with

Hi, I'm using a Junghanns Quadbri ISDN card on some lines from the Austrian Telekom. Things are working, the only missing stuff is to add a "0" as a prefix to each incoming call, to make it possible to answer missed call lists. I'm using the 0 as the prefix for outside lines. I've experimented a little with the prefix settings in zapata.conf, but without success:

I have connected asterisk 1.0.7 with Avaya Definity via E1 with a TE100P Digium Card. Inbound calls are working perfectly and I dont have any problem. But when I try to make an outgoing call with my softphone (xlite) I am getting the following messages. Hungup 'Zap/13-1' Executing Dial("SIP/IZ-bc0a", "Zap/g1/3118") in new stack Called g1/3118 Channel 0/1, span 1 got