similar to: MWI - One mailbox, multiple extensions, lots of lights!

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Long story short... Snom's ... Retrieve button... works when MWI is *NOT* lit but does *NOT* work when it is lit. Any advice Useragent : snom360/6.5.2 Function: F_RETRIEVE [root@pbx ~]# asterisk -rx "show version" Asterisk 1.2.13 built by root @ pbx on a i686 running Linux on 2006-11-17 16:35:22 UTC [gateway] exten => 201,hint,SIP/201 exten =>

I have finally set correctly the Message Wait Indicator feature on my Grandstream (I was using the wrong context - I thought the documentation referred to the {mailbox=210@Context} extension context not the voicemail context). Voicemail.conf [internalvoicemail] 20 => 1111,dean,dean@cogs.net,,attach=yes 30 => 2222,jodie,jodie@cogs.net,,attach=yes Sip.conf [20]

We are using Bellsouth 8867 phones on our TDM400B FXS lines (asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI (according to the manual it works with voicemail from the telco that sends a FSK signal). The dialtone stutters when a line has voicemail, so I know that I have the mailbox setting right in zapata.conf, but the light doesn't go on. I am also getting

my biggest concern about defaulting the context to anything at all besides [default] is that you then have to remember to configure the voicemail.conf with the corresponding contexts. as it stands, you have the ability to do just that, but you don't have to. if you have several hundred extensions broken out by dozens of contexts, it might not make sense to force the voicemail.conf to follow

Hi all, I'm having sudden MWI problems. Everything else on the phone works fine though. I have three Cisco 7940s. Asterisk server is behind a firewall running NAT. (192.168.1.202/24) Phone #1 - On the same subnet 192.168.1.250. Everything works great. Phone #2 - On a different subnet, 192.168.2.0/24. Everything works fine except the MWI. It never comes on. This is over an IPSEC VPN, but

Hey there. I've been working on a project to integrate Asterisk with Exchange Unified Messaging via sipX using large parts borrowed from: http://blog.lithiumblue.com/2007/04/accessing-exchange-2007-unified_29.html ... and everything works surprisingly well. The one problem I have is MWI, or a lack thereof. Exchange 2007 doesn't support MWI of any kind (!), so I've been looking into

Hello, I am facing a problem I can't understand. I have several realtime SIP peers and from time to time, the mailbox field is not loaded in asterisk memory. The mailbox field is correctly populated in the database, but often, after an asterisk restart, the mailbox is not associated to the peer (just to understand, if I run "sip show peer 104-TEST", I see the Mailbox empty. If I run

Hi, Strange problem that I can't seem to see any past postings on. New installation on OS X server. Voicemail ok from the handset. When an email address is added for MWI notification, asterisk crashes after the email is sent. Sendmail/postfix logs show no errors and the email is sent ok regardless. If I run asterisk with -vvvvvvvvcg it runs quite happily, emails and voicemails

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

I've taken a look at: http://www.voip-info.org/tiki-index.php?page=Getting+MWI+on+Polycom+Phon es+to+work+with+Asterisk I've followed those directions but when I press my message key it doesn't dial the number specified... It actually dials 614p which is the user I register with. My MWI light works, and worked before following those directions, but... I can't make it auto

Hi, Is there a way in Asterisk 11 to use a single voicemailbox for multiple extensions while still hearing each extension's individual greeting? Use case: someone has 2 numbers and wants all voicemail messages for both numbers to end up in one mailbox. So when dialing 1234 and NOANSWER you would hear "the person at extension 1234 is unavailable" and the message would be stored

I have the following setup: - UAs registered with SER/OpenSER - SIP peers (non cached), extensions, voicemail setup (not message storage) defined in Asterisk 1.2 using Realtime When a message is left in the user's mailbox, no Notify message is sent to SER. 1. If the SIP peer is defined in sip.conf with a host=ser.domain.com then the notfy is sent to SER. 2. If realtimecache=yes is set in

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

We have several agents on queues, and want to indicate to them that they are logged in or logged out. We have tried several different ways, from changing the screen to presenting different service menus, but cannot get anything to be "in their face" (their words, not mine). One of our team has suggested, as the agents do not have voicemail, is to use the MWI on the 7940 phones to

My grateful thanks to whoever can guide me in implementing this... I have a need to place calls via Asterisk Manager Protocol to a legacy PBX and twiddle its MWI lights. By some means I get notified that an MWI light has to be changed. Via AMP: 1. Send an ORIGINATE command honking up an incoming port on the PBX via a TA804. a. I presume that the TA804 should be a SIP channel. yes/no? b.

I remember seeing something like this on the list a while ago, but I'm darned if I can find it. We have a number of Polycom IP501 phones, some of which have more than one registration on them. When a voicemail is left for a phone with only one registration, the MWI lights up and stays lit until the voicemail is listened to. However, on our phones with more than one registration, the MWI

I have a large group of 7960G's running Asterisk 1.2.4 using SIP 7.5. Most of the time the message waiting indicator works fine. Once or twice a day either an MWI is not sent to the phone or the phone misses it. I have not noticed duplicates being sent and I can't figure out the time, if any, a resend is made. Anyone know why I'm missing, loosing or not sending an MWI to the

Hello everyone, My setup: Debian squeeze Asterisk 1.8, DAHDI, libpri, compiled from source TE110P, attached to a Deutsche Telekom Octopus E Modell 300/800 I'm trying to get MWI for Voicemail working. In the same server I have also got an Eicon DIVA PRI card for testing purposes (it is integrated via CAPI and the chan-capi channel driver into my Asterisk). MWI works just fine there. I

Here's a link to it: http://forums.digium.com/viewtopic.php?t=4363&highlight= Regards, Scott -----Original Message----- From: Scott Keagy Sent: Monday, December 04, 2006 5:05 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [asterisk-users] mwi for voicemail not showing up for realtimeconfig. A while back I posted a fully functional though somewhat elaborate