similar to: PSTN->SIP->PSTN transfer problem

Hi, Perhaps there's something wrong in my config... I did some tests connecting Asterisk to an Ericsson MD110 PBX by setting up an h323 trunk. When dialling into asterisk I got some problems when the entire number is not in the setup message, i.e. I'm dialling digit by digit on the ericsson phone. Lets say I have 4001 in my extensions, and dial that from the Ericsson PBX, then the

Hi. Anyhone have any experience with trunking between Ericsson MD110 and Asterisk using H.323? I've tried both ooh323 and the /channels/h323 one in version 1.4.4 and 1.4.0 of Asterisk. ooh323 does not manage to establish the call (starts to ring but then disconnection when answering the call on the Asterisk end) but using the channels/h323 driver I can get the call established from

Hello all ! I have a problem with my IVR with terminate connection from PSTN phone Here is my configuration extension.conf [ivri] ;exten => s,1,Wait(1) exten => s,1,Answer ;exten => s,2,DigitTimeout(5) ;exten => s,3,ResponseTimeout(10) exten => ivr,1,Background(demo-congrats) exten => 1,1,MP3player,/mnt/linux/mp3/song/04.mp3 exten =>

I was just wondering if someone has experiences to use Asterisk in an existing Ericsson MD110 environment. Particulary I'd like to know if it is possible to use the MD110's system phones directly connected to Asterisk. I'm not very familiar with it but would it be possible to use ADSI with these phones? Are they more like analog or more like digital phones or is the protocol even more

Hi. Calling from Ericsson MD110 via H.323 trunk to an asterisk 1.4.4 I get the call established but no sound heard on either end. What is the best/correct way to try and see what codecs Asterisk is using on each end of the call as it passes through Asterisk? And is there any way to see that voice is in fact being passed through Asterisk during the call (some counters etc.)? Thank you

I have been asked by a potential customer whether we can connect an Asterisk box to an Ericsson MD110 that has an E1 port with ISDN-USR. They are unable or unwilling to upgrade their E1 port to QSIG. Has anyone here had experience of successfully making such a connection? I have found a couple of hits on Google that suggest it "should" work, but I'm after something a little more

Hello all, I was wondering if someone already wrote something to support a serial connection(ICU) on PABX's that's used for signaling. What I currently have is a connection between an Ericsson MD110 and * with analog trunks. Problem with this is, that all CallerID info is send over a serial link (ICU). Is there anyone who knows if there is support for this on * or to find the

Hi, i managed to connect to Ericsson MD110 with PRI at last. And made a successful call thru asterisk to ericsson. But when i try to call from ericsson to asterisk i got an error on asterisk side. And i couldnt figure out why. Here's my extensions.conf about incoming calls. [DID_span_1] include = DID_span_1_timeinterval_all,${timeinterval_all} DID_span_1_timeinterval_all] exten =

Hello all, as good? It would like to make a question, asterisk supports the protocol qsig, for interconnections in ISDN with equipment Siemens HiPath 4000 or same Ericsson MD110, so that it could identify to the name and the number of hosts and also to use some features of asterisk in the Siemens/Ericsson equipment. Greetings Josu? -------------- next part -------------- An HTML attachment was

Hi, i know i am asking a lot of questions lately in this forum..sorry about that first of all. :) Ok, here is the deal.. I am trying to make a hybrid system with an ericsson MD110 and asterisk. Internally we have 4 digit phone extensions on ericsson.. and so in asterisk. So, what i want to do is to call pbx side without adding 9 or etc to the begining of the number from asterisk clients.. For

Hi guys! We have a call centre that has been moved across from an old Ericsson MD110 PABX to an Asterisk server with those in the call centre using X-Lite as their softphone. I'm trying to get Agent presence configured so that X-Lite gives the operators a visual indicator of their status - logged on, off and on "pause". I'm using chan_agent for the agents, so agents are

A little off-topic: I have the following hardware: 2610 XM NM-2V VIC-2BRI NT/TE IOS loaded: flash:c2600-ipvoice-mz.123-5d.bin" I get the following error while booting: %C542-1-UNKNOWN_VIC: VNM(1), vic daughter card has an unknown id of FF Is the VIC-2BRI compatible with the 2610XM? What IOS needs to be loaded? http://www.cisco.com/en/US/products/hw/modules/ps2641/products_tech_note0918

I've been trying to get a new asterisk box setup with Broadvoice for over a week now. I have it connecting and registering with them according to 'sip show registry', I can't dial out through it, but it does dial out through my regular phone line. I'd like to set it only to dial 911 through that line and have all other calls go over voip. I've checked out a bunch of

Hi people, I've got Asterisk running nicely with two 7960s and hooked into our MD110 via a cisco AS5300. All is wonderful with the world...except, what is the deal with features like group pickup and so on... I have no idea what codes are available, what they do, etc...is there either a standard * is conforming to, or some doco of what features are available? (heh, yeah

Hi, I am currently trying out the asterisk@home (version 1) release of Asterisk, and I want to configure it as follows: Calls from regular telephony network (PSTN) come in through my VoIP provider over SIP and outgoing calls to the PSTN should be routed through the ViOP provider onto the PSTN network. I thus have no direct PSTN connection, but only a SIP connection. Incomming calls

All, I'm haveing a bit of trouble getting my head around H.323 and call routing with Gatekeepers, Zones and intra-zone calls - hopefully someone who is more informed in things H.323 will be able to point me in the right direction...? I already have a mature network of Asterisk boxes dotted around the UK and overseas with hundreds of extensions and our own number-plan/dial-plan in the form

Stephan, Ok, I'll re-state the problem... I have two devices that I want to talk to each other: 1. an Asterisk PBX 2. a Damm Cellular TETRAFLEX digital radio system (www.damm.dk) both devices are effectively "gateways" because they have many subscribers behind them. The Damm Cellular system controller is based on Windows-XP Embedded and its sub-systems used the OpenH323

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

s/receiveing/receiving/ Marc. diff -aNpRruz -X /etc/diff.excludes rsync-3.2.7/rsync.1.md devel-3.2.7/rsync.1.md --- rsync-3.2.7/rsync.1.md 2022-10-16 13:27:30.000000000 -0600 +++ devel-3.2.7/rsync.1.md 2022-10-16 13:27:30.000000000 -0600 @@ -245,7 +245,7 @@ to be copied to different destination directories using more than one copy. While a copy of a case-ignoring filesystem to a case-ignoring

Motherboard ASUS CUSL2-C with 815EP chipset and two Intel 82559 Pro/100 Ethernet cards exibits the following. dmesg reports usual text only a few seconds after reboot. Later it displays a single line with a fragment of ipfw log, e.g. 167 213.131.11.152 in via fxp0 which seems to change with each new activity of ipfw. Files /var/log/dmesg.today and /var/log/dmesg.yesterday rotate daily as usual