similar to: chan_capi with an AVM C4 connected to 4 BRI-lines in PTP-Mode

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

hi all it seems like whatever I do, I can't use more than 1 BRI on my AVM C2 with chan_capi. Both channels seem to work, but not at the same time. And - yes - they're connected to different NT boxes :) Any ideas? kapejod? -- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356 Computers are like air conditioners. They stop working when you open

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi; I've been asked to take a (remote) look at an Asterisk@home system running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5 It has an AVM c2 ISDN card which is plugged into what I believe to be a couple of BT ISDN2e "System Access" (i.e. point to point) connections. We've placed a support call to BT to find out how these lines are actually provisioned, but

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi, Reading http://www.asteriskguru.com/tutorials/bri.html , it seems PtP is the way to connect businesses but if you read http://public.swbell.net/ISDN/connect.html you would think the opposite. Can anyone elaborate a bit PtP or PtmP respective advantages ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Good day, anyone out there running an ISDN pbx behind an Asterisk server with an AVM active card? At this moment Asterisk is connected to the internal ISDN bus of the PBX, but I want to control the calls coming in from the outside, before sending them of to the PBX. Any BTDT is greatly appreciated. rgds pos

hello, i change my isdn line to ptp mode and i have some trouble to configure chan_capi in that way. What is the correct setup - e.g. if numbers are 123456x - where x can be from 0 to 9 ? regards Marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/

I'm now up&running with - mISDN with avmfritz driver for Fritz PCI card - chan_capi from debian recompiled with a patch (see below) - EuroISDN with Point-to-Point (ptp) mode (Austria) - With Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k from debian sarge But am having some problems: 1) I needed to patch chan_capi.c from debian sarge (see below) to give the new channel to asterisk in state

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi there, i'm in debian sid 3.1 with kernel 2.6.7, * last cvs & chan_capi 0.3.4b; nt1+ with 2 bri in ptmp (http://www.voip-info.org/tiki-index.php?page=DDI) i tried to install avm c4 following step by step http://www.voip-info.org/tiki-index.php?page=Asterisk%20How%20to%20connect%20with%20CAPI step 1. i compiled capi 2.0 support in kernel

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

On 10/12/15 15:49, Leon Fauster wrote: > Am 10.12.2015 um 11:11 schrieb Michael H <michael at wemoto.com>: >> >> >> On 10/12/15 10:02, Leon Fauster wrote: >>> Am 10.12.2015 um 09:37 schrieb Michael H <michael at wemoto.com>: >>>> >>>> I'm trying to disable USB storage devices in Centos7.1.1503. >>> >>> on EL6

I am going to try and use a passive AVM fritz BRI card for my * setup.. Here is the thing.. I need to order my BRI from BT.. The service that looks to be the one to use is what they call ISDN 2e becasue this has the option to setup hunt groups across multiple ISDN2e lines so I could add another line later to get 4 channels.. According to the BT website in order to use the hunt grouping across

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if