similar to: Dell PowerEdge SC420 for Office Implementation???

Thanks! So aside from the lack of redundancy, will it perform well and scale to utilize a full T1's worth of calls through to the legacy PBX? We would probably build a backup server from old equipment and rsync the configuration files. Thanks again! > -----Original Message----- > From: William Boehlke [mailto:william.boehlke@signate.com] > Sent: Friday, May 20, 2005 3:33 PM >

We're using an SC420 and using BRI with a quadbri Junganns card, with IAX softphones and one hardphone. Working well except that we sometimes get dropped connections between IAX and the server with a max retries exceed message, which comes from the chan_iax driver code. The BRI side of things looks like it is fine. I had been thinking it might be a network issue but now wonder if it is an

Hi, I have a Dell Poweredge SC420 and a SC430. The SC420 has an ICH6 chipset and works ok with Xen. The SC430 has an ICH7 chipset and the SATA detection fails. I''ve tried 2.6.11.10 and 2.6.12.5 kernels, with Xen 2.0.7, Xen-testing and Xen-unstable, all with the same results. I''m using the same hypervisor and kernel binaries, so problems with the compiler environment etc. have

Hi, I am attempting to connect my dell SC420 to a 32" LCD at 1366x768. I have attached my currect config file and currect X start log. How do I massage the xorf file to run at the native resolution of the LCD? It currently runs but is in a virtual mode. The screen scrolls. Any help is appreciated. I am using Centos 4.1. Jerry -------------- next part -------------- An embedded and

Hi people I am new to Xen and having some trouble getting it up and running. I am trying to install it on a Dell Poweredge SC420 that has CentOS (RHEL3 clone) installed. The error that I am getting when I first try to boot into the Xen kernel, after having installed the binary and adding the necessary lines to grub.conf is : ---snip--- md: Autodetecting RAID arrays md: autorun ... md: ...

jglucky@blueware.net wrote: > Has anyone attempted or have had any issues getting Asterisk and > Digium cards working on a Dell SC420 server? I have it up and running on 2 SC420's with TE110P cards. Haven't had any problems as of yet (knock on wood). Dell SC420 TE110P 2x40 GB SATA drive in a RAID 1 setup (Linux 2.6 kernel needed for SATA drives; turn off RAID detection in BIOS).

Has anyone on this list succesfully managed to get two (or more) TDM04 (with four FXO each) working on a Dell PowerEdge server? If so, which model? Was it a hassle? I'm doing a seven-line installation and a callbank seems like overkill, I just don't want to get suck with a PowerEdge that gets into an IRQ mess. Thanks in Advance, Tom Hayden

Hi, Any folks on this list who have installed CentOS 6.3 on the new Dell Poweredge R815 servers? How was your experience? Thanks -Surya -- Surya Saha Department of Plant Pathology and Plant-Microbe Biology Cornell University, NY, USA http://www.linkedin.com/in/suryasaha

Subject: [Sharing] CentOS 8.2 (2004) Linux Server is Compatible with Dell PowerEdge R640 1U Server Good day from Singapore, I have just installed CentOS 8.2 (2004) Linux Server on Dell PowerEdge R640 1U Server for "Donald Trump and Xi Jinping Investment Company LLP" (fictitious/fictional company name used) in Singapore on 11 August 2020 Tuesday. I can confirm that CentOS 8.2

Hi, I want to install * and te405p on Dell Poweredge 1850. Can I do that successfully? Any one has successful experience on that scenario? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050607/fb7408a1/attachment.htm

I went to RedHats' page and found hardware requirements and it said that the Dell Poweredge 6300 is a supported hardware. Then I went to linuxcare.com and it does not list the machine. Before I look like a buffoon, or continue to, Redhat will run on this machine, right? I appreciate the help. Thanks, --------------------------------------------------- Tony Ricker Technology Coordinator

It turns hard to make XEN 3.0 running on my middle-sized server. Now when XEN 3.0 is released I first successfully put it on several PCs and then decided to probe it on SMP and PAE enabled Dell PowerEdge 6800 server. And experienced intermittent hangs just after dom0 comes up. The [login:] prompt comes up and the server hangs completely for a while and in some 2-10 minutes releases just to let me

Hi all, In this moment I have the opportunity to install asterisk in Poweredge 1400 Dell Server (PIII, 2 GB of RAM). I wonder if any of you have any experience running asterisk (+ Digium cards) on this kind of hardware, any comment about know problems or good experiences are welcome. Thanks in advance. Alejandro Acosta,-

Hi, I've been asked to find a server that is capable of running the Digium TE410P card. We usually get Dell PE servers and after a quick look I think the PE 1800 has the required slot: Six Total: 2 PCI Express (x8 lane & x4 lane); 2 x 64-bit/100MHz PCI-X; 1 x 32-bit/33MHz PCI (5v) and 1 x 64-bit/66MHz PCI Has anyone got this hardware, does it work with the card and asterisk? Thanks,

All, Seems like the latest CentOS 7.6 and I are not playing well together, these days. I'm attempting to use our pxeboot setup to install the latest CentOS 7 on a Dell PowerEdge R830. The install starts then gets to a certain point and hangs. That certain point is: FADT indicates ASPM is unsupported, using BIOS configuration Now I've tried to see where the Active Server Power Management

Hi, Is this server silent enough to be installed beside users in office environment ? http://www.dell.com/content/products/productdetails.aspx/pedge_860?c=us&cs=04&l=en&s=bsd Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070316/e657ef4d/attachment.htm

This works fine. Message: 26 Date: Tue, 7 Jun 2005 17:22:23 +0800 From: "Ma Zhiyong" <mazhiyong@sohu.com> Subject: [Asterisk-Users] te405p and dell poweredge To: <asterisk-users@lists.digium.com> Message-ID: <004501c56b42$6a12fcd0$7301a8c0@hylaclient> Content-Type: text/plain; charset="gb2312" Hi, I want to install * and te405p on Dell Poweredge 1850. Can I

Hello everyone, I'm considering getting me a quad-core Dell PowerEdge 860 to run Asterisk. Anyone else using this model? Any tales of woe and sorrow I should know about? Then, in a couple of weeks, I'm thinking of getting a Sangoma A108 and giving that a try. Same question with that one - any quirks I should be aware of? Girts -------------- next part -------------- An HTML

Hi all, Just found out that the Poweredge R300 cant even load the CentOS 5.2 64bit installer. Had to revert to Ubuntu. Seems its a driver problem. Pity, but does this kind of case apply to many other servers? --- OSCC MAMPU MyMeeting Version 2.0 Release http://knowledge.oscc.org.my/solution-areas/application/mymeeting

Does Centos/RHEL 4.4 supports the CERC 6-Channel SATA RAID Controller that comes with the Dell PowerEdge 830 Tower Server? -- ------------------------------------------------------------ Erick Perez Panama Sistemas Integradores de Telefonia IP y Soluciones Para Centros de Datos Panama, Republica de Panama Cel Panama. +(507) 6694-4780 ------------------------------------------------------------