similar to: RTFriendsCache=yes help Voicemail MWI help

May be I have fiddled too much with my sipura settings but I can't get it to give the stutter tone when there is a new voice mail waiting on the asterisk box. I can either get a stutter tone all the time or not at all. Anyone got this working. Thanks Chris

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

I have many remote locations that dial into a central server to retrieve voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a local (to them) Asterisk server that dials the main server thru IAX. I have trained them to check their voicemail via the emailed WAV file, however some of them are, how shall I put it, idiots*, and insist that they *have* to have the MWI indicator

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

Sorry for the partial post a moment ago With help I got two phones communicating - PCMA/PCMU was the problem. Next stpe is to try voicemail. VM works fine, I can leave a mesage and then retrieve it - but no MWI on the phone and no stutter dialtone. I promise I've spent the requisite 4 hours + on google etc. but have really no further ideas. The setup is 2 Grandstream phones (latest

My grateful thanks to whoever can guide me in implementing this... I have a need to place calls via Asterisk Manager Protocol to a legacy PBX and twiddle its MWI lights. By some means I get notified that an MWI light has to be changed. Via AMP: 1. Send an ORIGINATE command honking up an incoming port on the PBX via a TA804. a. I presume that the TA804 should be a SIP channel. yes/no? b.

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

Using a TE410P with Zhone 24FXS channel banks to power standard analog phones I can't seem to find out if it's possible to support FSK or voltage type message waiting lamps. I don't want to use stutter dial tone because of the dramatic difference in per phone cost. TIA

Dear List, I'm having a blinking MWI light on the snom 320 even when there's no message waiting in Asterisk. We've managed to make the voicemail button work using fromdomain=192.168.0.1 in sip.conf vmexten=2500 (our VoicemailMain application extension in extensions.conf). We also added notifymimetype=application/simple-message-summary also in sip.conf to allow SIP simple MWI

Hi.. I am about to replace my aging Nortel Venture system with an Asterisk system and 6 Polycom IP 501 phones, and a couple sipura 841's for less used areas. We have 3 phone lines here. One is SBC, one Vonage, and one Voipjet... One hangup is that I can't figure out how to pass through a voicemail waiting indication from SBC. This is important because my wife and her family all

asterisk-users-request@lists.digium.com is believed to have said: >I don't mean to be rude to everyone who responded to this question, but >I think that everyone is answering the wrong question. The point is that >the message waiting indicator doesn't light up, at all, ever. All that >happens when messages are waiting is that the display blinks and the >phone gives a

I am trying to set up the Message Waiting Indicator (stutter tone/light) so that my cisco ata-186 will let my phones know there is a message waiting. However this does not seem to be very well documented. I found this on wiki mailboxnumber@context ... where does that go? Do I put it in my SIP.conf definition for my cisco ata, or where. In my SIP cisco definition i already have a

I'm trying to get the Telco MWI recognition working in asterisk-1.6-beta7. I'm told that it's supposed to work provided my telco support FSK MWI signalling. I have Verzon FIOS. I believe I have FSK MWI signaling as I can hear the standard stutter tone when I pick up a live handset in front of my asterisk connection. I have the Verizon line attached to a TDM400 card, port 4. I

Howdy I have a question regarding support for picking up when the telco sends a MWI message. My client's setup is a small office with three incoming lines on a TDM400P with iaxy's and a Grandstream as extensions. I am using CVS Head from yesterday. (I was resolving a different issue.) Since they only have two voice lines, with the third as a fax, I am using voicemail from the telco.

Hi, I'm using the SPA-2000 with firmware 1.06 on the Asterisk PBX, which works great for taking and placing calls, but for for some reason I can't seem to clear the stutter dialtone by either calling the extension I'm on, or the voicemail system on the Asterisk PBX. If I call my voicemail access extension directly, It tells me I have no messages waiting, yet when I hang up, then

I have Asterisk voice mail setup locally. It works great, I'm impressed! Some details about my system: I'm using a TDM22B card to interface with both the PSTN and a VOIP provider. I'm running 1.2-beta from CVS. I have a regular VTech phone plugged into one of the FXS ports. Asterisk is able to indicate when a local voicemail message is waiting via the LCD display of my analog phone.

Stutter tone when voicemail in boxHi, I'm having a problem getting Asterisk to make a stutter tone when a voicemail is received. It used to work, but since I rebuilt my server I can't get it going. I've set put a line in the sip.conf file: mailbox=100 to check it, but it's not doing the stutter tone ! I am using the stable version of asterisk from the CVS tree. Any help /

Has anyone seen the following problem? Until recently, I couldn't understand why some extensions on my * system would have a "congestion tone" as soon as I picked up the handset. A little sleuthing through the logs and the source code led me to understand that * thought it had seen the extension go off-hook, send some DTMF tones, and then wait. * treated this situation as a

AFAIK, this is not possible - but I'll throw it out there anyhow... I subscribe to telco voicemail, for the event that all my pstn lines are in use. Telco gives me a stutter-tone dialtone when I have a message waiting. Can a Zap card detect this stutter-tone and perform some action? I'm using TDM400P+FXOs and SIP devices. Thanks