similar to: chan_capi, chan_misdn and chan_modem

Could someone please comment on the current state of chan_capi, chan_misdn and chan_modem channel drivers in terms of functionality and stability. Specifically, which channel driver would be best for a passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that chan_capi distinguishes between junghanns and non-junghans cards, and that chan_misdn is better suited for general misdn

Hi all, Does anybody of you have the winbond w6692 working with the mISDN/chan_misdn.so? When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1" error. The /var/log/messages file says: "MISDN free_device: entitylist not empty" I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7 chan_misdn build from chan_misdn-beta-0.0.3-rc6

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb

Hello all I found a bug in the chan_capi driver (really a not implemented message handling and then a false error condition) and I guess I have wrote a patch to fix it (basically I searched the internet for other capi open source implementation an borrowed the code snippet) but I don't know where to send the report and bugfix. I also found some miss-behaviours that I would like to share

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hi, I am currently running several * boxes on 1.0.9 with HFC chipset ISDN modems using i4l's hisax driver and chan_modem. Will I be able to use my existing chan_modem setup with 1.2.4 or 1.2.7 or will I need to change it to use bristuff or chan_capi? I want to do the upgrade with as little changes as possible. Thank you Marnus van Niekerk -- "Opportunity is missed by most people

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and

Hello all, I just subscribed to this list and I hope this is the correct place to ask for help with this issue. Today I checked out asterisk via cvs and I was able to compile, to install and to run it. Everything was fine so far. Then I downloaded chan_capi 0.3.3 from www.junghans.net and tried to compile it, too. Unfortunately I get an error in line 1205 when compiling chan_capi.c : too

Hi all! I'm getting an error when I try to start asterisk with chan_misdn. I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel, mISDNuser, asterisk, chan_misdn). I got mISDN from http://isdn.jolly.de/download/v3.0/ I'm using a CVS Snapshot of asterisk, which was checked out about 5 hours ago. This is the error: [chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:

A plea to all! Has anyone had any success with two or more avm fritz pci cards with either misdn, chan_misdn, or chan_capi, and any version of linux 2.6.x? I have managed to get misdn to load under 2.6.13 and detect two cards using misdn-capi and chan-capi (using capiinfo and capi info under asterisk) - but the second card/controller doesn't answer or dial calls. But if I try misdn

Hi, Has anyone had experience installing it? yum install asterisk-chan_misdn I'ts the latest Trixbox Distro version and same issues exists if add in the Trixbox repo. FAILS as per below: I have a ISDN single port PCI BRI card installed and detected. __________________ Loaded plugins: fastestmirror, kmod Loading mirror speeds from cached hostfile * addons: www.ftp.saix.net * base:

Quick question: Is there a way to distinguish between calling MSN's when using chan_misdn? More info: I've got my ISDN2 (EuroISDN) up and running here in Romania with 1 base number plus 5 MSN's. Now I want to my * to do different things when receiving a call on from different MSN's (like forwarding the call to my FAX machine or forwarding the call to my mobile). The obvious way

Hello everyone. I've got a HFC ISDN card that I'm using with chan_misdn and it basically behaves like crap. Echo is waaay worst then echo I get TDM400 card, sound is "choppy" (there other side is allays complaining about sound interruptions) and to top it all it detects fake DTMF's all the time. Is this a chan_misdn problem or is it a card problem? I really need to get

Hello everyone. My land-line provider (Romtelecom) has a very nice offer for ISDN. All in all they offer me a digital land-line with 1 base number + 2 MSN's and that would make a grate addition to my full-time home office. Romtelecom say they're providing EURO-ISDN and the line is compatible with any euro-isdn compliant equipment. They say they'll install a NT at my office and this

Hello! I have tried to compile the capi module (http://www.junghanns.net/asterisk/downloads/chan_capi.0.3.5.tar.gz) on fedora2 today. ----------- MAKEFILE -------------- ..EXPORT_ALL_VARIABLES: INSTALL_PREFIX= #ASTERISK_HEADER_DIR=$(INSTALL_PREFIX)/usr/include ASTERISK_HEADER_DIR=/usr/include/asterisk #MODULES_DIR=$(INSTALL_PREFIX)/usr/lib/asterisk/modules

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: PGP.sig Type: application/pgp-signature Size: 186 bytes Desc: Signierter Teil der Nachricht Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20040624/fe4cdcbf/PGP.pgp

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi i've installed asterisk by last cvs and i note res_parking.c is not anymore there; chan_capi-0.3.4b INSTALL file require: in /etc/asterisk/modules.conf insert the line: load => res_parking.so load => chan_capi.so running asterisk i get: [app_capiCD.so]Jul 21 15:32:26 WARNING[1076988448]: loader.c:242 ast_load_resource: