similar to: Inbound ANI & DNIS format

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Good Day list, Need assistance determining the best place to read up on whether Asterisk can help me out. I have a situation where I need to do the following <PRI from Telco> ------- <Analog Channel Bank>------------<Proprietary Box> | | | | | | <PRI Port 1 of Digium Quad T1> <PRI Port 2 of Digium Quad T1> | | | | | |

does anyone know how to route a call coming in with ANI*DNIS* Oct 31 12:47:41 VERBOSE[30056] logger.c: -- Executing Set("Zap/49-1", "DID=1231234*4812*") in new stack I tried making a route for _.*4812* but that matched everything rather then just the dnis i wanted.. any ideas? I would preferably like pass the callerid along to my extensions, but for now the important

Can someone in Asterisk'land subscribing to 800 service explain to me how to setup extension.conf to route calls based on the incoming DNIS/ANI. For example I want to route 3 incoming 800# coming across a trunk group to all land in the same queue. So I guess I am asking how to perform DNIS/ANI based call routing? -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan

I receive calls over a T1 with callerid and then *ani*dnis*. I am able to strip out the ani and the dnis in the dialplan but when I try to set the caller ID to be the ani, it looks ok but then if I do a NoOp callerid on the next line, I get unknown. Here is the section of my dialplan: exten => _*NXXNXXXXXX*NXXNXXXXXX*,1,Set(ANI=${EXTEN}) exten =>

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Yes its a T3 split into seven trunk groups with one D channel and NFAS on each. Can you explain the cut function or point me somewhere please? Thanks, Steve -----Original Message----- From: Alexander Lopez [mailto:Alex.Lopez@OpSys.com] Sent: Mon 4/10/2006 12:51 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Subject: RE: [Asterisk-Users] ANI and DNIS Seperation on

My company is based in Australia and we have a need to be able to present CLI (ANI) and DNIS to an analog extension. Currently our PABX vendor is saying they can only deliver CLI between the first and second cadence. The system will collect calls via an aggregate of ISDN PRI services from the PSTN and then direct them to the analog extensions in a hunt group configuration. It is important that

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hi, ? I run the program testcall with one E1, it works fine; I receive DNIS and ANI for making calls and answering calls. ? When I start the Asterisk I receive call from outside correctly including DNIS and ANI, and receive the following messages: ? Sep? 7 10:29:59 WARNING[12167]: Answer Call Sep? 7 10:29:59 WARNING[12167]: MFC/R2 UniCall/2 Call control(5) Sep? 7 10:29:59 WARNING[12167]: MFC/R2

Alexander, Thanks a million, you really saved me some time on this one. -----Original Message----- From: Alexander Lopez [mailto:Alex.Lopez@OpSys.com] Sent: Mon 4/10/2006 1:11 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Subject: RE: [Asterisk-Users] ANI and DNIS Seperation on a PRI(TelephonyNumbering Plan (E.164/E.163) (1)'*4105556654*8005550215*' ]) from the

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They