similar to: SIPURA SPA-2000 webserver dead after firmwareupgrade

I just got a refurb Sipura SPA-2000 and was able to assign it an IP address with DHCP and ping the device, but then I ran the firmware upgrade utility to bring it up to spa2k-2.0.13g which seemed to work just fine, but after it rebooted I cannot connect to its webserver for configuration. I can still ping the unit. When I use the built in voice menu it reads back the right IP address, webserver

Hello list, I have several SPA-2000's and 3000's scattered about the Internet (all behind NATs). Because I do not qualify as an ITSP, Sipura will not license their "Sipura Profile Compiler" so that I can have the units remote upgrade, remote re-configure, etc (via TFTP or HTTP). This is extremely annoying. Right now if I have to make a config change to any of these

All, If you currently own a Sipura SPA2000, avoid going to the sipura website and upgrading the firmware. I upgraded my SPA2k a couple of days ago from 1.0.9 (what it came with) to 1.0.18 off the site, and I am having issues with my SPA rebooting itself every 3-10 minutes for no apparent reason. I have been in touch with the *excellent* sipura support folks, and they are working with me to

I heard Sipura had really awesome documentation on the SPA-2000 and SPA-3000, but you have to email them for it. When I did, they said I had to get it from a reseller. It's been a while since I bought my units, I don't even remember where or who they were bought from. Can somebody email me the documentation for these devices? I'm quite interested in knowing what every one of their 200+

Hi, I'm using the SPA-2000 with firmware 1.06 on the Asterisk PBX, which works great for taking and placing calls, but for for some reason I can't seem to clear the stutter dialtone by either calling the extension I'm on, or the voicemail system on the Asterisk PBX. If I call my voicemail access extension directly, It tells me I have no messages waiting, yet when I hang up, then

I had a Grandstream 286 at my home hitting my Asterisk box at the office, all worked well and I received phone calls fine until the device just up and died. I replaced this unit with an SPA-2000 because I have been impressed with the Sipura devices and decided to use them for most of my needs in the future. Problem is that my phone attached to the device rings shortly after power up of the

I am looking at some lower cost phone to use with Asterisk. What is the ArtDio IPF-2000 or the Sipura SPA-841 like? Also, I see voipsupply.com has an ArtDio IPF-1000 listed, is this a new or an old model? I cannot find any information on it. Adi

If I understand correctly the Sipura people are the same guys that made the Cisco ATA (Komodo phone) or what ever. I'm going to get one of the Sipura SPA-2000 to use and abuse with *.... I have seen the web interface.. John over at Chagres was nice enough to let me login to one and look around a few weeks back... I'm impressed .. if you guys care to buy one

Some people on this group may have understood from messages posted here that the Sipura SPA-2000 is not currently available for shipping. That is not the case. Voxilla.com has the Sipura SPA-2000 available for immediate shipping, and has had them since late November. The price is $109.95, and it comes with a month of free VoicePulse service with activation fees waived (a $65 value). In return

Hello all, So i am new to asterisk and very green when it comes to Linux, so don't beat on me too bad :) I just set up * on Red Hat 9.0 last night... everything "seems" to be configured coffectly, I can start * no problem and get the CLI prompt... now here is my question... I have an account set up with VoicePulse Connect! and also have a Sipura Spa-2000... i am trying to get make

When I dial a PSTN (via * with Digium Quad-E1) number, I hear two sumultaneous ring tones. One is coming from *, the other I assume is from the ATA. Is there an intelligent way to get around this?

James H. Thompson wrote: > The Sipuras pull their config from a HTTP or TFTP server. > Now that they support XML config files, all you need to do is put the > file on your web server and point the sipura to it. > The Sipura will pull down the config from your web server, nothing > special required on the web server side. > And only a single line entry on the Sipur

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA

Thanks! Thanks! Thanks! I've got it work!!! :-) Message: 13 Date: Sun, 16 Jan 2005 12:17:21 -0000 From: "Bill Seddon" <bill.seddon@lyquidity.com> Subject: RE: [Asterisk-Users] failed to compile zaptel on redhat To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" <asterisk-users@lists.digium.com> Message-ID:

I figured out what was going on with the lack of/stuck on stuttered dial tone. Apparently, there are two voicemail directories being referenced: /var/spool/asterisk/voicemail/default, and /var/spool/asterisk/voicemail/local. The sip phones were using /var/spool/asterisk/voicemail/local to dump VM messages into, yet the MWI looks at /var/spool/asterisk/voicemail/default. Does anyone know why

I am located in the UK, and I am using Sipura spa-2000 adapters to connect analog phones to a voip network. The network connects to the PSTN as well via the Sipura spa-3000 adapter. I would like to provide surge protection for the spa-2000 and the spa-3000 adapters. 1. For spa-2000, fxs port: What is the maximum tip-to-ring voltage before damage to the the adapter occurs? 2. For spa-2000,

To me it's a error if I can't complete calls using the ATA configured to use the g726 codec. I just tried it usign a sipura SPA-2000 (preferred codec: G726-32) and I received NOTICES and WARNINGS, but I can't complete a call. On a zap channel: -- Executing Dial("SIP/2007-e4d8", "Zap/1/2217008") in new stack -- Called 1/2217008 -- Zap/1-1 answered

Hi, the topic says it all really. Does the Sipura 3000 detect and report UK clid correctly? thanks Mike

I'm experiencing a problem with a Sipura SPA-941 not available for incoming calls after Asterisk & Freepbx upgrade. I can dial out with the phone gto any other internal or external ext. It is registered with the Asterisk server. When I dial the Sipura directly from any other extension, it goes directly to vm. I have other Sip softphones that are working fine. A sip debug when calling the