similar to: Cisco ATA & Call Waiting

I have recently upgraded my firmware from v6.3 to v7.4. Now when the phone is booted or rebooted, the initial screen "Initializing Vlan" takes forever to initialize before it initializes IP. Any ideas/Thoughts? (Trying not to Revert back to v6.3). -C -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anyone come across the Cisco ata 186 not passing *70? When I press *70, the ata just goes back to a dial tone. The strange thing is, its only *70 and not the reset of the 70's. *71, *72, etc all go through fine. I've tried removing the the dialplan all together from the ata to try and let it pass, but no go??? If I setup an IP phone to its extension, *70 goes through fine, so i know

Anyone have call waiting working on the ATA-186 connected to Asterisk? Other VoIP phones seem to work, but I can not get the ATAs to allow call waiting. Christopher M Iarocci Network Admin JD Posillico 631-249-1872 X244

I've done something similar at home, but made my dialplan such that I can dial either 10 or 11 digits locally. I don't use a "throw away" digit at all. Any 7, 10, or 11 digit call will be appropriately mangled and sent out the PSTN / VoIP provider. ________________________________ From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On

I have a Cisco ATA-188 with two POTS phones and latest stable cvs. In any situations with call waiting (existing connection and calling again) the second call cause both calls to drop. This is the same for "internal" extensions and from external (ZAP and SIP). It seems to be a "502 - The transaction could not be executed, because the endpoint does not have sufficient

The details for the Australian cisco ATA186 are below: > -----Original Message----- > From: Tony Du [mailto:tony.du@action.com.au] > Sent: Tuesday, 8 July 2003 4:31 PM > To: 'Adam Goryachev' > Subject: RE: [Asterisk-Users] ATA 186 in Australia > > Hi Adam, > > I sold a Cisco ATA186 I1 2 port adaptor (Cisco code: > SW-SMH-UL-ATA-2P)to you on 16/10/02) >

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Hi All, I'm looking at setting up a Asterisk system, and hope to use ATA 186's with it. Im in Australia, and am getting mixed answers to if its the I1 or I2 i need, does anyone have any experience with using ATA 186's in Australia Also, can anyone recommend a good place to obtain these locally? Cheers, Steven

I have an interesting problem. I am attempting to install a payphone utilizing a Cisco ATA-188. The payphone actually works, but there are some timing issues. What happens is you pick up the payphone and the ATA grabs a line and goes offhook. While you monkey with putting money in and dialing the number, you are eating up the time before you get the offhook reorder tones (or howler tones

Hello, I've got a Cisco ATA 186 from Vonage plugged into my Asterisk box with a X100P card. This works great for the most part, but I'm having a disconnect supervision problem. I suspect the Cisco device doesn't provide any sort of analog disconnect supervision when it gets a SIP BYE message indicating the far-end has hung up. This causes Asterisk to leave the channel up

For anyone who is interested, I have a working tftpd (modified wvtftpd) capable of serving configuration, dialplans, and ringtones to Cisco 7960/7940 and ATA-186 devices that are located behind NAT firewalls. As TFTP is not a very firewall/NAT friendly protocol, I had to break some rules to get it to work with these cisco devices. It might cause problems for other TFTP clients, but it works with

Hello. I have a linux and two sip-ata's, a sipura 2002 and a GS ht-386. I also have three sipphone numbers. I can connect the atas to the sipphone accounts and I get a dial tone and I can call my house and it says, "Thank you for using SipPhone..." Using asterisk, I have the ata's registering to my computer and I register two sipphone numbers with my computer. When I

I am trying to set up the Message Waiting Indicator (stutter tone/light) so that my cisco ata-186 will let my phones know there is a message waiting. However this does not seem to be very well documented. I found this on wiki mailboxnumber@context ... where does that go? Do I put it in my SIP.conf definition for my cisco ata, or where. In my SIP cisco definition i already have a

Hello list, i am using: asterisk CVS-10/13/03-11:54:33 chan_capi-0.3.0 ATA-186 V2.16.1.ms over MGCP Situation: ISDN calls ATA ISDN speaks with ATA ATA-Phone presses Flash and speaks to another one (SIP/snom200) ATA-Phone hangs up ISDN talks to SIP/snom200 snom200 hangs up The incoming extension of ATA keeps busy for a time (20 sec?), even its not off-hook anymore! Any ideas? -- Swapping

I have seen the list of codecs for the ATA 186's but not sure if it was 100% or not. I want to know really is it possible to run GSM or ilbc on them or is a G729 lic the only way to get a low bandwidth codec? This is the list of codecs that I have seen. RxCodec and TxCodec?Configure the codec ID. * G.723.1?Codec ID 0 * G.711a?Codec ID 1 * G.711u?codec ID 2 * G.729a?codec

For all thos Asterisk users not on the FWD list, it works for me!: -----Original Message----- From: Free World Dialup - The Future of Dialing [mailto:FWD@LISTSERV.PULVER.COM] On Behalf Of Leonidas Piagkos Sent: donderdag 12 juni 2003 0:58 To: FWD@LISTSERV.PULVER.COM Subject: Re: [FWD] FWD losing Registration Hi Don, All you have to do with your ATA is to set the following parameters as :

Hi all, I have sincerely spent the last 2 hours googling for ATA<MAC>.cnf.xml file for a Cisco ATA 187 and I am not going anywhere. Either no one is using this thing out there or it has worked very well for them. Would there be someone of this list using the TFTP managed Cisco ATA 187 with Asterisk? I would be very grateful if you can share a copy of the file with all the confidential

For those of you wanting to salvage your Cisco ATA-186 after inadvertent locking, or after recovering your devices from a vendor who has locked them, here is a rainy-day project for you: http://www.sst.com/downloads/datasheet/S71077.pdf The above document gives exact specifications on the 4mb flash EEPROM that stores all program and configuration data on the ATA-186 (aka Komodo.) If you

I use cisco ATA 186 ( Version: v2.16 ) with sip protocol and asterisk as pbx. I need feature called as 'three way calling' or 'transfer with consultation'. Registering,calling and 'blind transfer' work fine. Is this feature provided by sip clients or by asterisk itself ? What I have to configure in ATA and what keys I have to press on my phones ? Three way calling is

i have been trying to get a newly liberated (from vonage) cisco ata-186 (sip ios v3.1) working properly with asterisk. my client is behind a linksys wrt-54g, which up to this point hasn't proven to be a problem (i have several sipura spa-2000's and polycom phones working just fine behind them). (i'm running cvs-head from yesterday). after looking at the various suggestions,