similar to: HFC-S

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

This is my first posting to the list. Thus hopefully the question has not been asked several times before... I'm trying to install asterisk on a PC using Debian Sarge but without any real success... Problem: I may get the Asterisk packet (Debian version) installed using 'apt-get install asterisk', but that does not include the bristuff from Junghanns

Hi, I'am having some problems with new mainboards and 3xHFC-S cards. The the first problem was with interrupts, I mean if HFC-S card was using interrupt i.e. 21 or higher - it didn't work. Solved by disabling APIC. However, still the driver behaves a little bit strange. If card 0 & 1 is TE and 2 is NT, TE works fine, but NT is not working at all. If card 0 is NT and 1 & 2 TE - all

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hi Alessio Yes, the problems you report do seem similar to the issues I had. I found on the Dells that the audio prompts were very choppy and played slower than normal. Occasionally there would be 'bursts' oav a second or so of 'good' audio. I also suspected IRQ issues but the Dell Mobos had no way of adjusting them. Best thing is to try and get the card on its own unshared

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

We just had * crash on us - no calls could be made / received. We had to kill -9 the * process. Checking the error logs, I came across these two lines, with the times matching the crash: Aug 26 13:48:00 WARNING[19282] pbx.c: Local/6024@AgentQ-94ce,2 already has PBX structure?? Aug 26 13:48:00 WARNING[19282] channel.c: Thread -1105359952 Blocking 'Local/6024@AgentQ-94ce,2', already

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Hi all! I am working with asterisk and trying to get it work in DHCP network, where asterisk gets a DHCP address as well as other computers (IP-phones). So far, I've have got asterisk working with static IP address where phones are getting their IP from DHCP server. Is it possible at all to phones to find asterisk server if it gets random IP address from the DHCP server also? I mean, is there

I'm trying to use an hfc based pci card with asterisk but every call fails falling in the congestion extension. exten => _0.,1,Dial(${TRUNK}:${EXTEN:${TRUNKMSD}}||tr) exten => _0.,2,Congestion Looking in the syslog i can see: isdn: HiSax,ch0 cause: E001B it seems that this is a terrible error when arrives... hard to tell what is the cause. Also terrible is finding a lot of material

Hi! I have installed two hfc-s cards to handle my pstn calls. I use mISDN with capi, so capi.conf is edited. I have tested both separate and cards are working well. But they are not working together. It seems that when i set up settings for the other card: ;capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=50 incomingmsn=* controller=1

Hello! Im very new to asterisk. At first i will need it to send wave files to an specified number over an isdn card. What will i need to do this? Which modules i need for this job and how to setup the asterisk server? I know its complicated question but i dont know how to set it up. Have read some how-to?s on voip-info.org like asterisk and isdn4linux but dont see the right way to get it

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hi all, I've been working with * for a long time now, but only with analog FXS/FXO systems. I am venturing towards setting up a box in Germany now and I believe that requires a Fritz card? Do I even have to use the Fritz cards? Why not a Digium card.... We have 2 ISDN lines ( --> 6 handsets) so I'm guessing that will require 2 Fritz PCI cards (they have 1 port only). Then

We are looking to lose the TDM400P in favor of an ISDN-BRI solution. This should get rid of static on the line (at least any static generated by our half of the circuit), right? I am a total virgin to ISDN. I understand that we need two BRI circuits to provide four voice channels, and that the hardware to speak to the BRI circuits can be passive or active, with the active type being much more

Hi all, I got into a strange problem here. I've got an asterisk box with bristuff-0.2.0-RC7k, and a HFC PCI ISDN card, running in NT mode. The ISDN card is connected to a S0 bus and to a Siemens ISDN PBX. Two phones are connected to the ISDN PBX and are successfully getting calls from the asterisk box. When dialling from one of the phones, the ZAP channel seems to be missing out on some of

Hello, I've been using * for quite a while using AVM C4 card and a few Grandstream Budgetone 102 hard phones plus couple of HandyTone 286. Echo is a big problem. I am getting used to it, but some users complain. Anyone has experience w/ regards to echo comparing the AVM C4 with two HFC-cards? Before shelling out time and money, maybe someone else already has done so, and could tell me if