similar to: 3 Party Conference & ZapHFC

Hello, I have the following problem with HFC card and Alcatel PBX 4400: - I want to connect Alcatel PBX and Asterisk with HFC card (zaphfc driver 1port S0/T0 interface card) - BRI line is configured at PBX to T0 trunk - In asterisk I have loaded zahfc driver in NT mode and also set in zapata.conf NT mode, point-to-multipoint. - I am using cross "isdn" cable to PBX -

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi, I'm setting up an asterisk server with this hardware configuration: AMD Athlon 1000 Mhz 256 MB ram 3ware ATA raid controller 2 * Ethernet controller 2 * ISDN HFC controller One ethernet controller is connected directly to the internet (public IP) One ethernet controller is connected to the internal lan One ISDN controller is connected to the public telephone network One ISDN controller

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Maybe this is rather a hardware question, but I am posting it on this list because the probability of someone else of you having tried this is greater here than other places I can think of. I have an ISDN card that is setup in NT mode using the zaphfc driver in bristuff, and I got it working perfectly with one ISDN phone using a crossover cable and 100 ohm termination at the end of the cable.

Hi, I'm tring to setup a ISDN HFC card in NT mode, but I have a problem with ztcfg that always report a problem regarding FXS/FXO signaling. Is someone have ever seen this ? Loadind the zaphfc module seems ok.... -- insmod ./zaphfc.o modes=1 ------------ zaphfc: card configured at mem 0xc89eee00 fifo 0xc29e8000(0x29e8000) IRQ 19 HZ 100 zaphfc: Card 0 configured for NT mode zaphfc: 1 hfc-pci

I need some help with installing Asterisk with ZAPHFC on my Linux system. I've installed Red Hat 9 with kernal 2.4.20-8 and upgraded it to 2.4.31-9. I've donwloaded bristuff (several versions) but all fail to compile. There seems to be some includes missing in /usr/includes/linux. Although I have significant experience with other platforms, I'm new to Linux and would need someone to

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Hi, currently I got the following problem: The system contains a HFC-PCI card, it's running without problems under zaphfc. Now this system also should send/receive faxes. Receiving faxes works with rxfax (spandsp) but txfax is not comfortable enough and doesnt bring the demanded results. So an older external ISDN modem and mgetty-sendfax is used for sending faxes. I'd like to send the

Hi everybody, I had an ISDN card with winbond chipset and isdn4linux, but there was a lot of echo when call from SIP to ISDN, so I buy an HFC chipset card (Conceptronic c128i). I downloaded and compiled bristuff-0.2.0-RC5 and everything is going fine. The sound quality is excellent, there is no echo, but i have a strange problem. Sometimes calls made from SIP phones to ISDN just finished

If you check the latest info in bristuff this bug is now fixed in 0.2.0-RC7, too bad that zaphfc is not yet finished for single HFC-S cards but if you have quad or octobri it should work On Fri, 11 Feb 2005, Stefan Gofferje wrote: > Hi folks, > > in the past, I have encountered several situations where internal ISDN > phones, connected to a HFC-S card, running in NT mode,

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk