similar to: Major problems with TDM400 and specific telephones: suggestions?

OK, I have a Asterisk @ Home 1.0.7 server with two Digium TDM400 cards, one 4 port FXO and one 4 port FXS. When I plug an analog cordless phone into the TDM40B card and setup a ZAP extension, the phone rings in and you can answer just fine. The weird part is when you try to get dialtone from the cordless handset it rings all of the other extensions... One other thing to mention is that the

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L

Hi, I'm running * 1.2.7.1 on Red Hay 9.0 w/ a TDM 400 2 x FXS, 1 x FXO. I'm using a VTech cordless that makes three short beeps when someone another extension is picked up, presumably this lets you know if someone is trying to listen in.. Everything works, except the VTech now makes the three beeps everytime you try to use it, even if another extension is in use. It seems as though the

Ouch, part reset, quickly restoring reality (0) Power alarm on module 1, resetting! I have looked though a lot of email on this issue, and no one seems to have the answer. How many people are seeing this on a TDM400 card? Does anyone have a "REAL" answer to it. Yes, I do have the power connected to it! Regards Garry Taylor

Hello! I just wanted to tell everyone that I have successfully used a TDM400 with an IBM Netfinity 5600 server. I used PCI Slot 3 (the first hot-swap PCI slot). I had a ServeRAID 3L controller in slot 1as well, which managed the server's array. Other than that, there was nothing extra installed. 2x667MHz PIII, 1GB RAM, 4 x 18GB hot-swap SCSI drives. The only problems I had were Ouch

Hello, everyone After having spent several time to look for any solution for my problem, I decided to write here. Here is the problem got a Digium X101 FXO card and Digium TDM400P alias freshmaker (1 fxs module on it on first port ) in my asterisk box. The X101 works perfectly. The problem comes from the TDM400, when i plug a tested working phone on it , i get no dialtone; the goal is to

Any clues as to what this is? Google isn't much help. Both cards have the power connector plugged in, and both randomly give me static instead of a dialtone, or an outside line. Cards are 1 4 Port TDM400 FXO, and 1 4 Port TDM400 FXS. Computer is a Compaq Proliant ML330 The full error is as follows: Ouch, part reset, quickly restoring reality (0) Power alarm on module 1, resetting!

Ok, I've seen discussion before on doing transfers (attended and unattended), there seems to be much confusion over it. As things sit, I've been trying (unsuccessfully) to do transfers with a zap channel (analog phone attached to TDM400). I have no idea what I'm missing. My current understanding is that I need to have transfer=yes in zapata.conf, do a flash hook, dial the 2nd

Hello! In spite of a number of complaints, I have tried to use a TDM400 on a Via EPIA-MII motherboard with a 1.2GHz C3 CPU. cpuinfo and interrupts are included at the end of this e-mail. I have had no problems with it so far that I can attribute to the computer. I have, though, had continual problems with a certain telephone... Anyway, this module currently has 3 x FXS modules and 1 x

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

G'day all, A weird problem has just started happening with my * server, and I've googled myself stupid looking for help. My system is latest CVS, a TDM400P with two FXS modules, two X101Ps, and VoIP connections (SIP, SCCP & IAX2). My wife complained about her extension (analogue, on one of the TDM400 ports) being dead -- no dialtone. I had to shut down *, then unload and reload the

Today I had channel 1 on my TDM400 go to sleep, verified by pluggin in known good telco lines in various combinations on channel 1 through 4 - problem is channel 1, not anything external. So after seeing lots of stuff on the list re: TDM400's I power cycled, removed board and let linux say nothing's home, replaced board, told linux to ignore it etc. No OS/asterisk/etc changes made on

Hi, I have just built my home Asterisk box into a better PC that became available (still only a P2 350 but it only has to manage 1 analog line).. Anyway I have built it on Fedora Core 1.. I have an X100P and a TDM400P (1 module installed).. These cards were working fine in my older PC that was running my Asterisk at home.. The inbound calls via the X100P to my sip phones are working great..

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

for the same price, siemens dect phones with sms feature display caller name !!!! --------- Message d'origine -------- De: Wilson Pickett <spamsucks2005@gmail.com> A: Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users@lists.digium.com> Objet: Re: [Asterisk-Users] Major problems with TDM400 and specific Date: 25/03/05 18:00 > > &gt; Sorry for my bad

Sorry everyone, I know this has been hashed over a bunch of times but I can't find anything that pertains to specific cracking and popping on the FXO modules of a TDM04. This happens on inbound or outbound calls. This is the first install I have done with a TDM card for FXO modules so please, be kind if I am missing something really simple. Damn I wish everyone wanted t-1's or

hey all, I want to set up a phone network at home. I have to phone lines (one traditional line and another provided by my internet provider (voIP)). So what I would like to do is get a Digium box and connect my two lines to it and then use several cordless voip phones with the ability to transfert call from one phone to another. What kind of digium hardware i need to do this? also I will use

Sorry in advance if this is a FAQ... I've got a working Asterisk setup based on A@H 2.2. I have a TDM400 card with 2 FXS and 2 FXO ports; PSTN connections come in via the TDM card. I haven't been able to get inbound fax with spandsp and rxfax to work. Occasionally an all-text fax will come in, though it's usually badly corrupted, but in most cases, it would appear that the call is

I've been having ongoing problems with my TDM400 FXS ports occasionally not picking up all digits dialled from my analogue handsets. There appears to be no set pattern to it, although number 1 seems to be slightly more frequently missed than other numbers. I've played around with RX Gain settings and used ztmonitor to arrange the input signal between 50 and 75% of the maximum value

Hi, I'm relatively new to Asterisk, and I'm looking to build a tiny system for home use. For context, at home I've got a line from Vonage (last I heard, they won't give out SIP credentials and let you use random hardware/software), which comes out as an analog line with a dialtone, and I'll be treating that as if it were a regular PSTN connection. I also work from home,