Displaying 20 results from an estimated 6000 matches similar to: "te110p sometimes green, sometimes stays red on stable cvs ?"
2005 Mar 18
1
Te110P initial installation problems ?
Hi,
thank you for last info. we've tried to use te110p but failed. We're quite
surprised that cable wasn't included with the card as any documentation, at
least on HW setup and installation, yet cable pinout for connection to PRI
interfaces....
1. We have followed instructions on your site and from Beronet guide, but
card just keeps blinking and nothing happens (also no useful
2007 Jul 22
0
te110p stays in red alarm
Folks,
I installed a te110p to connect to an E-1. Ensured the jumper is on
for E-1, installed the card, and got the following from the phone
company:
hdb3 encoding (verbally confirmed ccs)
euroisdn switchtype
pri signalling
So I set up zaptel.conf:
span=1,1,0,ccs,hdb3
bchan=1-15
unused=17-31
dchan=16
loadzone=us
defaultzone=us
Card tries to come up but goes into RED alarm. Occasionally cycles
2005 Aug 08
4
TE110P flashing red/green when PRI connected
Hi
I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts ....
I can't seem to find anything in the log that suggests what could be wrong
.....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,
2005 Aug 09
1
TE110P flashing red/green when PRI connected ... continued
Perhaps everything isn't as spiffy as I thought
When running zttool the card still reports as internally clocked
Zaptel.conf:
# Global data
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
loadzone=se
defaultzone=se
And as pointed out by Peter I do get a lot of D-channel warnings ...
Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
And
2005 Mar 22
1
Problems loading zapata module under suse 9.2 (cvs stable from 5 days ago) ?
Hi,
I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any
problems. We're using te110p and wcte11xp module that is autoloaded by Suse
9.2.
Card goes green after reboot, but this meesages appear in logs:
Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major
196
Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa
2007 Feb 26
3
Yellow or Red alarm on TE110P ????
i get this message with a red signal on TE110P card:
*****************
TE110P: span configured for...
Calling startuo (flug is 4099)
wcte1xxp: Setting yellow alarm
*****************
what does mean ?
thank you :)
2005 Sep 26
0
TE110P Hanging up & sometimes not picking up on E&M T1
I'm getting unstable behavior with my newly installed TE110P T1 card. It
hangs up any incoming call anywhere from 20 seconds to 6 minutes.
Frequently, when you call back on our incoming T1 there'll be an
automated announcement (maybe from the telco?) stating "we are unable to
complete your call at this time". I simultaeously get a yellow alarm on
the system and shortly
2005 Aug 16
1
DISA over Zap (TE110P) issues on * STABLE 1.0.9
Hi !
Did anyone had issues/managed to solve issues with DISA over Zap channels on
* 1.0.X (STABLE) ?
I have a situatuion where DTMFs that should be recognized in DISA work over
SIP channels and do not work over ZAP channels (Zap channels are on TE110P)
I have in default context:
exten=> 299,1,DISA(no-password|default)
and I have SIP extension 200 in [default] and I have Zap trunk which
2005 Mar 16
0
Stable CVS or Head CVS for using TE110P ?
Hi,
I'd like to know which version of Asterisk performs best and most stable
with TE110P.
I don't need any other features (it'll just terminate interasterisk calls
without any other feature - so there is no need for CVS Head features or
? ).
Any info on setting up secure interasterisk IAX connections (only one way) ?
With IAX authentication by certificates ?
Thanks in advance,
2005 May 24
5
Red Alarm TE110P
Hi!
I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands.
I get a Red Alarm on the line.
Is there any way of debugging this? I've tried some configs that should
work but without success. Is there any way of telling if the cabling is
correct or what else the problem could be?
Thanks!!
Remco
2007 Sep 26
1
Supermicro PDSME+ and TE110P [ ref:00D36mPe.50033qy57:ref ] NEW CASE 22828
Hello,
Digium support kindly proposed to ship a TE120P card to help resolve the
issue.
I plugged in the card, and introduced the loopback plug. I cleared the
red alarm for a while and then i started seeing alarm switching from
Yel/Recovering to Blue/Rec with a lot of IRQ Misses.
I call Digium that assisted us, and we noticed IRQ sharing with the VGA
adapter and the Ethernet port.
I changed
2007 Mar 09
0
Boot order of 2 TE110P and 1 TDM400P in the same
Fedora Core 6
regards, Pablo.
On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote:
> Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this:
> ??? Alarms Span ??? OK Digium
2007 Apr 27
0
Problems with Digium TE110P
Hi everyone
I have a Digium card TE110P and after plug it, turn on the computer and
configure, the LEDs don't light up in spite of what Digium FAQ says about the
LEDs:
When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP?
... The TE110P LED's will light up RED when the span is configured and kernel
module is loaded. If configured correctly and a circuit or channel bank is
2005 Aug 30
1
TE110p and E1
Hi All,
I have configure my Asterisk as follow (using Asterisk@home):
[zaptel.conf]
span=1,1,0,ccs,hdb3,yellow
bchan=1-15,17-31
dchan=16
loadzone = uk
defaultzone=uk
[zapata.conf]
[channels]
switchtype=euroisdn
pridialplan=local
prilocaldialplan=local
internationalprefix=00
nationalprefix=0
usecallingpres=yes
busydetect=no ; not need on pri
callprogress=no ; was yes but wiki says experimatley
2007 Mar 08
3
Boot order of 2 TE110P and 1 TDM400P in the same machine
Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this:
??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P
2005 Oct 12
1
unloading TE110P bristuffed module cause kernel panic
Hi folks,
I've already searched the mailing list but no one else seems to have my
same problem.
I'm using Asterisk with the following configuration:
Fedora Core 4 (but I also tried Fedora 3)
1 Digium TE110P
1 TDM40B
1 HFC-S 'Cologne'
bristuff 0.2.0-RC8o (zaptel 1.0.9.2)
I compiled right, I can load kernel modules but when I try to unload
wcte11xp module (the one
2007 Feb 21
0
Trixbox ;TE110P ;DELL OPTIPLEX GX240
Hello every body,
I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to
the latest version. I've 2 cards installed in the same pci channel via
a bridge or plug i don't know exactly what's his name( but a card (1
pci) that gives 2 pci channels)
the first card is TDM400P: it's ok
the second is TE110P: it's not ok . No led is on neither the red nor the
2006 Jun 22
0
Motherboard Selection For TE110P & TDM400P
Hey there,
What recommendations does anybody have as to motherboards known to work
well with the Digium TE110P T1 interface cards and the TDM400P analog
POTS interface cards? We currently make use of the TE110P for our T1
(esf w/ b8zs - not a PRI) and have experienced many issues caused by our
PBX's motherboard. Additionally, we built a server to become our new
PBX, but that machine runs
2006 Apr 05
0
TE110P errors
Hi All
I have a TE110P card connected to a PRI line. In my zaptel.conf I have:
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
loadzone = us
defaultzone=us
and my zapata.conf is:
[channels]
context=inbound-pri
switchtype = national
pridialplan=unknown
;pridialplan=international
signalling = pri_cpe
callerid=asreceived
busydetect=no
usecallerid=yes
hidecallerid=no
callwaiting=no
callwaitingcallerid=no
2007 Mar 05
2
Rx+,Rx-,Tx+,Tx- of TE110P
Hi everybody,
i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P
and also if you can tell me have to made a cable like that??
Modem Teleco <-----------Self Crosscable------------>Asterisk
Rx+ <--------------------------------------------------------------> Tx+
Rx- <--------------------------------------------------------------> Tx-
Tx+