similar to: X100P and Toshiba PBX

I'm posting here in case anyone else runs into this and needs some help. I'll probably update the voip-info Wiki pages on Toshiba integration in a bit. Asterisk 1.6 makes things a bit easier than what is on that page. I'm integrating an Asterisk server with a Toshiba Strata system at my office. Right now, it is driving some VoIP phones (Cisco ATAs with analog phones plugged into

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

Hi, I am currently integrating our company's Toshiba PBX with the Asterisk version 1.2.1. I bought Quad T1 card, and making the port 1 to connect to PSTN PRI (use "pri_cpe" in zaptel.conf") and making the port 3 to connect to Toshiba PBX (using "pri_net" in zaptel.conf). The first stage goal is to just adding the Asterisk relay between PSTN and Toshiba system. The

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

I have asterisk successfully dialing out using a X100P over a normal analogue PSTN line. But when I try to dial out over an analogue line that goes via a hardware PBX the call asterisk does not dial. Is there a configuration change I should make ? I am thinking of something like not wating for dial tone.

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other

Hello! We are using the Digium 405PP card, and getting the following messages: Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 8 on Primary D-channel of span 1 My config file is below. We are trying to set up D-Channel on channel 24, 1-23 in trunk group 1,

Hello, community. Several months ago Toshiba Inc. released a new communicator - "Toshiba Portege G900". All device's features are greate, but in practice things are going another way: communicator is really SLOW. Toshiba users have found that G900 is using nVidia GoForce 5500 Chip in it and it seems like it's working partially, because of an incomplete driver. We have written a

I have googled, and wiki'ed until blue. Is it possible to put T1---*----Toshiba CTX ? I have a TE405P, with one interface programmed for the T1, I am not sure how to program the 2nd port to mimick the T1 to the Toshiba. The Zapata.conf [channels] switchtype=national context=from-pstn signalling=pri_cpe usecallerid=asreceived echocancel=yes echocancelwhenbridged=no echotraining=400

I set up a TE405P to go T1---*---Toshiba. I have the channels configured, and can place calls from the Toshiba, through * to the t1. Incoming calls work great to *, but if they go to the Toshiba, I get a hangup. I think the * is sending the call to the wrong span. I have 2 spans, span 1 from the T1, span 2 to the Toshiba. The bchannels show as 0/1 through 0/23 on both spans in * when it starts.

I have recently changed jobs and I now have to administer a Toshiba DK424. I would like to integrate Asterisk with this Toshiba PBX. I am quite familiar with Asterisk but I have absolutely no idea about this Toshiba. To make matters worse the manuals for this system are missing. What I would like to do is place Asterisk in such a way that we can extend the Voicemail boxes and possibly add a few

Steve, Here is the config, I pulled from my server, that works with D'Link Phones: Main Menu -------------------------------------------------------------------------------- SIP.CONF [general] port = 5060 ; Port to bind to (SIP is 5060) ;bindaddr = 0.0.0.0 ; Address to bind to (all addresses on machine) bindaddr = 67.109.153.236 disallow=all ;allow=ilbc allow=gsm allow=ulaw

I found some postings from Google (notably from Mark Spencer) about successful integration of a legacy Toshiba Strata system and Asterisk. I am also facing that current dilemma. The general legacy solutions that I can come up with is very easy -- either making Asterisk a "proxy" (or frontdoor) to the Toshiba system, or have it operate behind the Toshiba via regular extensions. I'm

Hi I have the X100P card which as to sockets (LINE - for fxo line ) and PHONE (to connect a n analog line) This card is setup as fxs_ks I was getting dial tone but suddenly no Dial Tone....Help appreciated.... When I try to route the Call using - Dial Zap/1) to this FXO Line I get this error: ------------------------------------- linux*CLI> -- Executing

Hi, I had ordered a TDM40B and developers kit a few months ago. I have everything installed and working, with one exception - sound quality. When placing a call it sounds like a very bad cordless phone - lots of hiss / static in the background. This even happens with the dialtone, though it is much worse one the call is connected. This does not occur when the phone is directly connected to the