similar to: Te110P initial installation problems ?

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

Hi, I've recently benchmarked btrfs v0.11 & v0.12 against ext2, ext3, ext4, jfs, reiserfs and xfs. OS: Ubuntu Hardy Kernel: 2.6.24(-5-server) Hardware: --------- Fu-Si Primergy RX330 S1 * AMD Opteron 2210 1.8 GHz * 1 GB RAM * 3 x 73 GB, 3Gb/s, hot plug, 10k rpm, 3.5" SAS HDD * LSI RAID 128 MB Fu-Si Econel 200 * Intel Xeon 5110 * 512 MB RAM

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Alle, I was wondering if anyone is using 4.X on any Fujitsu Primergy hardware and what type of experience they've had. I know that FJ provides separate drivers for all the supported hardware that are supposed to be RHEL4.X compatible, but I have my doubts. Best Regards, Camron Best Regards, Camron -- Camron W. Fox Hilo Office High Performance Computing Group Fujitsu America, INC.

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hello, I'm having problem with a wildcard TE110P. As soon as I load the module (wcte11xp for kernel 2.6.10), it spawns a yellow error with or without an E1 plugged-in. Any one managed to set it up in France? Here are my files: zaptel.conf: span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 zapata.conf: [channels] language=fr context=default switchtype=euroisdn pridialplan=unknown

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Guys. I have an issue with a te110p card and also some tdm04b cards on the same system: Zttest returns this for the tdm04b cards: [root@mollendo ~]# /usr/src/zaptel-1.2.4/zttest 38 -v Opened pseudo zap interface, measuring accuracy... 8192 samples in 8191 sample intervals 99.987793% 8192 samples in 8192 sample intervals 100.000000% 8192 samples in 8192 sample intervals 100.000000% 8192 samples

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

Say I had a crossover cable that connected a Mitel SX200 to a TE110P and the pinout was done as such: 1 - 4 2 - 5 5 - 1 4 - 2 (the 5 and 4 are transposed on the left side) Instead of the proper way of: 1 - 4 2 - 5 4 - 1 5 - 2 What would the results be? We have had the former as our cabling for a few months and the connection has been fine. Slip errors here and there. But we have had major

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

I am trying to test the T1 card in our legacy PBX but the connector to the card is a 15 pin serial cable. I would like to make it myself so I can try this test today. Does anyone have a pinout for it? I just made a T1 RJ-45 loop back to test my TE110P and it tested out fine. I'm trying to resolve some timing issues and a tech from Digium is going to ssh in and walk around my asterisk server

brett@websmyths.com wrote: > Also - an outside chance - make sure Tip and Ring > are correct. You could be getting ground loops - depends on the noise. > I am having noise and slip errors between my TE110P and a legacy PBX T1 card. Could this be the same symptom? The connection is made using a 15 pin serial on the T1 Card side to RJ48 on the TE110P side. I can't determine what the

Hi all, I have installed a TE110P in a BOX but when I load zaptel module I can't see any device in /proc/zaptel. And led of the card is green. My zaptel.conf is the next: span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=es defaultzone=es and cat /proc/pci throguh next: PCI devices found: Bus 0, device 0, function 0: Host bridge: Intel Corp. 82845 845

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

Hi, I wonder which PRI interface card is most stable and supported for EuroISDN and Asterisk ? Are they stable enough ? Any tips ? Thanks in advance, regards, Rob.