similar to: ISDN phone Hold-Problem connected to QuadBRI/Zap

Hello all, Recently I purchased an QuadBRI card from junghanns.net after some playing around, reconfiguring dialplans etc with the exception of 1 thing everything seems to work: I seem to be unable to set the outbound callerid. The dutch telecom operator (KPN) provided me with 4 MSN's on 1 BRI interface. In the past years I'm more then used to setting the MSN without the leading 0, this

Hello, I have a problem, and I'm looking for you help. When I dial certain number my calls are getting dropped. I initiate the call, I hear IVR, then I am being transfered to operator, and then suddenly I get ISDN DISCONNECT message. I had this type of problem some time ago, and I thought it was a problem on the other end. But now this is a second time it occurred and I want an expert to

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

Salve, I'm somewhat stuck on how to get DTMF working with my setup and googling didn't yield anything similar. My setup consists of one CAPI-capable board (AVM Fritz!DSL) connected to a BRI (T-ISDN), one HFC-S board running in NT-mode connected to an internal S0 bus with some ISDN devices (DECT stations, TA) and, of course, some ethernet interfaces. ISDN standard used is Euro-ISDN.

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

We are still having problems getting a Wildcard to work with a German E1 (PMX) interface. When starting asterisk it shows all B-channels starting up successfully (although our carrier told us only the first B-channel starts, if any at all). Incoming calls are not being signaled at all. (They seem to be intercepted by the carrier's switch, as no B-channel is up) Outgoing calls sometimes work,

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Hello, Configuration: Asterisk CVS HEAD 20050730 on RH EL3+ DIGIUM TE110P PRI card + euroISDN E1 I am trying to sort out the problem: 1. Provider's switch sends "SETUP"; 2. Asterisk receives "SETUP", rings allocated extension but does not send "Setup acknowledge" (or any other messages) to switch; 3. After 4 seconds of waiting of *'s response switch sends

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

picture. I know the firmware on the Nortel is old, so I'm guessing that libpri is sending something that the Nortel does not know how to handle. Is there a way to dumb down what libpri sends? From everything I've read PRI is an evolving standard - and older devices may struggle with newer extensions/developments. (This might be very handy for users trying to talk to old pbx's.) Is

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Yes its a T3 split into seven trunk groups with one D channel and NFAS on each. Can you explain the cut function or point me somewhere please? Thanks, Steve -----Original Message----- From: Alexander Lopez [mailto:Alex.Lopez@OpSys.com] Sent: Mon 4/10/2006 12:51 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Subject: RE: [Asterisk-Users] ANI and DNIS Seperation on

Hi all, I have an asterisk-server (cvs-head from august) connected to a carrier's switch (DMS/Euroisdn) via a te410p, and I am having problems with DDI (standard 'official pstn' number plus extra digits for 'internal' use) Basically, when the entire number (including the extra digits) is dialled via a redial or a programmed key, I see the entire called party number (including

Hi all, using latest asterisk-svn I want to reflect an video call incoming via an PRI EuroISDN channel to another outgoing PRI channel, and I want the the outgoing channel to have the exact same bearer capability < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Unrestricted digital information (8) < Ext: 1 Trans mode/rate:

Hi, I tried to use Early Media: exten => 1,1,Playback(demo-thanks,noanswer) same => n,Hangup() But when calling my extension I do not hear the voicefile - I only hear the ring tone. In the Asterisk-Log I can see, that the voicefile is played. I got the same result when using "Progress()" in the first priority. I tried "pri set debug on span 1" and got the

Asterisk 1.8.4-rc2 (and 1.8.3) DAHDI Version: 2.4.1.2 libpri version: 1.4.12-beta3 We are having a problem with getting the nationalprefix option of chan_dahdi.conf to work. National calls do not have a "1" added to them when nationalprefix=1. The PRI debug shows the call coming in as a National Call, but the dialplan sees the call without a 1. chan_dahdi.conf: <snip>

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and