similar to: MGCP Channel Lockup and other probelms

Hi all, i am using CVS-HEAD-08/13/04-12:00:00-BRI-stuffed-0.1.0-RC4a with Cisco ATA-186 3.1.1 atamgcp We are used to make an special ;) blind transfer like (Flash)Number(Hangup before anyone answers or ring). Then * crashes (see below) if the man in the middle is an cisco-ata-186-mgcp If one waits until the last one rings, then hangup, everything is fine. If one waits until the last one

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

Hi. I'm new in Asterisk with MGCP. I set up a MGCP user agent and start asterisk with the next configuration files. '--------------- extensions.conf ---------------------------------------------------- [general] static=yes writeprotect=yes [globals] ap1 => mgcp/aaln/ap200@64.76.148.186 [macro-apl1] exten => s,1,Dial(${ARG1},30,Ttmr) ;exten => s,2,Voicemail(u${MACRO_EXTEN})

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

see below I tried to call 98013356 from the following phone (from mgcp.conf) [iptlf03] host = 192.168.33.3 context = default inbanddtmf = 1 callerid = 22545062 line => aaln/1 Console output: == Spawn extension (capiring, 9988001133335566, 1) exited non-zero on 'MGCP/aaln/1@iptlf03-1' -- MGCP mgcp_hangup(MGCP/aaln/1@iptlf03-1) on aaln/1@iptlf03 -- Delete connection 4

I strange error messages when using mgcp and ata186 . This session is simply dial into 600 demo extension - echo test ... Handling request 'NTFY' on aaln/1@10.0.1.19 Transmitting: 200 29 OK to 10.0.1.19:2427 -- Endpoint 'aaln/1@10.0.1.19-1' observed '0' -- MGCP Asked to indicate tone: on aaln/1@10.0.1.19-1 in cxmode: sendrecv Posting Request: RQNT 306

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

I am trying to dial a mgcp extention from my sip phone and i am getting this error message. anyone got any idea? error I> -- Executing Dial("SIP/2204-5dc2", "MGCP/aaln/1@10.0.1.150") in new stack May 19 22:30:01 NOTICE[1251156800]: chan_mgcp.c:1104 find_subchannel: Gateway '10.0.1.150' (and thus its endpoint 'aaln/1') does not exist May 19 22:30:01

I've been trying to figure this one out for a while, but to no avail. I have my cisco ubr924 setup for MGCP with Asterisk as the call-agent. I have manually registered the endpoint in mgcp.conf. When I pick up the phone, I get no dialtone and debug shows errors. IOS on the ubr924 is 12.2. Any help is appreciated. from mgcp.conf: [ubr924] host=65.37.86.203 context = from-sip (just as a

I'm trying to link up Cisco MGCP-enabled router (residential gateway) with Asterisk, and it looks like some sort of protocol mismatch, could it be MGCP 0.1 vs 1.0? Look at this (x.x.x.99 is the router, x.x.x.98 is Asterisk): MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427MGCP read: NTFY 2 aaln/0@voip-gw1 MGCP 0.1 X: 0 O: hd from 192.168.154.99:2427Verb:

Okay, so I'm a noob. Asterisk looks very promising, so I say "thanks" and "good job" to all who contribute. My * test box is up and running with soft phones using IAX and SIP, so now I'm on to testing hard phones. I borrowed a couple ShoreTel 210 phones from somebody who had them on hand but they only support MGCP. I see that there's an mgcp.conf in

I have a DG-104S (which I reset to factory settings, it's DHCP'ing off my network, plugged into the WAN port). The system comes up, and I through the web browser set under Call Agent IP Address to: Notify Entry: dlinkgw@[192.168.1.1]:2427 (192.168.1.1 is the * server) I have RGW Name: and DNS IP addres the DNS IP of the MGCP box and DNS State disabled (not sure what to set it to) --

Hi all, I have VOIP network built with MGCP endpoints.The manufacturer of endpoints is ASKEY. I downloaded latest Asterisk software and found it very useful for me. I configured it and it seems taht everything works OK when I am testing it with one or two endpoints. After that I tried to move Asterisk to working network and replace existing call manager. It starts working and calls are

Hello all, I'm running Asterisk 1.2.35 with chan_mgcp activated. The process host around 2,4K users. Along the day I've got some debug reports like : Feb 24 22:25:42 DEBUG[28546] channel.c: Avoiding deadlock for 'MGCP/aaln/1 at 028421223635-1' Feb 24 22:29:04 DEBUG[28670] channel.c: Avoiding initial deadlock for 'MGCP/aaln/1 at 028421223635-1' Then, at

Hello, I've successfully installed Asterisk from last CVS and configured it for using with DLINK-DG104S as mgcp CPE and PGW2200 as external sip server. All are work fine at G711 codecs, but then I disable all codecs except g729 some calls failed (Not all calls. Some calls passed at g729 succesfully). All my devices configred to use only g729 and I don't see other codecs at mgcp or sip

Greetings; We are trying to get Asterisk up and happy at our site-we tried VOIP using Sphere about a year ago, spent a *boodle* on expensive hardware and services from a local "expert", but it never was happy. I'm brand-spanking new at VOIP, and I've learned a *ton* getting Asterisk breathing in the last couple of days. I have three Polycom Soundpoint IP 500 SIP phones, which

Hello, I`m try to make the attended transfer work Dlink DG-104S via FLASH, when somebody calls my phone I pickup and press flash to get a second line to call another extension. When I press flash I hear no dialtone, and only a long and then small beep. When I try to dial digits I hear again those long+short beeps, but the extension dialed is not ringing. If I pres flash again I get back to

I know this is not the most appropriated list to this, but I will try: Does anyone know what is the criteria to the generation of the transaction identifiers in MGCP? I mean, are they generated by a randomic method? I'm using Asterisk and MGCP eyeP Phone and observed that the RSIP and NTFY (methods created by the gateway) use high values in the transaction identifiers, while the RQNT, AUEP,