similar to: Stable CVS or Head CVS for using TE110P ?

Hi, we've installed te110p with Suse 9.2 on Siemens primergy. We're connecting to voxsteam i60 to test PRI interface. We have problems, after reboot sometimes it goes green, otherwise stays blinking red. How could we debug this situation ? Are there any common advices what to check ? Are CVS Head drivers better than CVS stable ? Why ? Do you also experience such unstable behaviour

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi, I'd like to setup oneway connection - so asteriskB can place calls on asteriskA and be safely authenticated with rsa keys. I just don't get any response on asteriskA. I've generated pair of keys: name.key, name.pub and put them on both servers - is it right to only have name.key on asteriskA and name.pub on asteriskB ? I get everybody is busy ... on asteriskB, and none

Hi, I've compiled Asterisk cvs stable (few days ago) unde Suse 9.2 without any problems. We're using te110p and wcte11xp module that is autoloaded by Suse 9.2. Card goes green after reboot, but this meesages appear in logs: Mar 22 11:28:51 linux kernel: Zapata Telephony Interface Registered on major 196 Mar 22 11:28:51 linux modprobe: FATAL: Error inserting torisa

Hi, I've spotted weird crash of Asterisk cvs Stable. I have defined queue in queues.conf : [prodaja] music = default announce = queue-markq strategy = ringall context = from-pstn timeout = 15 retry = 5 maxlen = 0 announce-holdtime = no announce-frequency = 30 announce-holdtime = yes monitor-format = gsm|wav|wav49 monitor-join = yes eventwhencalled = yes member => Agent/1000

Hi ! Did anyone had issues/managed to solve issues with DISA over Zap channels on * 1.0.X (STABLE) ? I have a situatuion where DTMFs that should be recognized in DISA work over SIP channels and do not work over ZAP channels (Zap channels are on TE110P) I have in default context: exten=> 299,1,DISA(no-password|default) and I have SIP extension 200 in [default] and I have Zap trunk which

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Hi All, Sorry if this has been covered in the past; I've tried searching the archives, but haven't had any luck finding a similar problem. Basically I have problems when using IAX2 (which I now understand is just IAX). I have three IAX connections setup - VoicePulse, IAXtel, and an Asterisk IAX<->PSTN termination provider here in Sydney (ATP) If I try to use the CVS STABLE version

Tie line is type em_w (old school stuff) to TE110P. Phone rings on the asterisk side, but the calling party does not hear the ring through sound. If I pick it up within the first two rings it goes through and I can talk otherwise our old switch drops the call. Anyhow...here is my config if anyone can shed some light on it. It used to work with HEAD a few weeks ago. -Matt

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

Hello, Digium support kindly proposed to ship a TE120P card to help resolve the issue. I plugged in the card, and introduced the loopback plug. I cleared the red alarm for a while and then i started seeing alarm switching from Yel/Recovering to Blue/Rec with a lot of IRQ Misses. I call Digium that assisted us, and we noticed IRQ sharing with the VGA adapter and the Ethernet port. I changed

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hello every body, I ve installed Trixbox 1.2 on "DELL OPTIPLEX GX 240", i upgreded it to the latest version. I've 2 cards installed in the same pci channel via a bridge or plug i don't know exactly what's his name( but a card (1 pci) that gives 2 pci channels) the first card is TDM400P: it's ok the second is TE110P: it's not ok . No led is on neither the red nor the

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

Hi All I have a TE110P card connected to a PRI line. In my zaptel.conf I have: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us and my zapata.conf is: [channels] context=inbound-pri switchtype = national pridialplan=unknown ;pridialplan=international signalling = pri_cpe callerid=asreceived busydetect=no usecallerid=yes hidecallerid=no callwaiting=no callwaitingcallerid=no