similar to: Broadvoice outgoing problems

Hello, Have a weird problem when using asterisk (1.0.6). There are certain numbers I cannot dial when using asterisk with my broadvoice account. No problems with inbound. With outbound calls, I can call some numbers (for example broadvoice customer support number) and unsuccessfully with some. However, when I configure my account directly on x-lite, I dont see these outbound problems. Here is a

Using AMP, the configuration I have used to work fine with Broadvoice. Now it gets a busy signal every time. I've checked "sip show registry" and it says it's registered just fine. I've tried "sip debug" and it shows calls coming in, but they always get a busy signal & I can't tell why. Here's a SIP Debug output: Sip read: INVITE

Connecting to proxy.dca.broadvoice.com Calls all of a sudden cannot be completed. Cannot ping proxy.dca.broadvoice.com Changed to proxy.chi.broadvoice.com pingable, but now get the following: Got SIP response 500 "Internal Server Error" back from 147.135.12.128internal error Called Tech Support... get dead air then carrier busy signal. Anyone else having

Hi all, I am using * as a PBX for a Broadvoice VoIP account. It had been working well since about last November, although not perfectly (similar disconnection problems, although I am pretty sure it had to do with my PPPoE setup, but I think these issues were resolved). As of a few weeks ago, though, I started having serious problems. Basically, I can start up * and connect to Broadvoice and

Well, you have *way* more files than we do... :) Il 30/03/2023 11:26, Hu Bert ha scritto: > Just an observation: is there a performance difference between a sw > raid10 (10 disks -> one brick) or 5x raid1 (each raid1 a brick) Err... RAID10 is not 10 disks unless you stripe 5 mirrors of 2 disks. > with > the same disks (10TB hdd)? The heal processes on the 5xraid1-scenario >

Thank you for the info Groeten. I have the TFTPD-HPA server address set to 192.168.1.9:69 I am unable to ping this address and I wonder if the server address should be the same as the network interface card (ethernet card) I am using. The files I want to upload are in /srv/tftpboot, so I'm not sure why the command cd /tmp was used. John At 03:21 PM 9/2/2015, Geert Stappers via Syslinux

Hi all I have registered my phone1 in asterisk server 192.168.0.9 and phone2 in asterisk server 192.168.0.6. Both are sip phones. i configured the extensions.conf file in both the server. the extensions.conf file on server 192.168.0.9 is exten=>301,1,Dial(SIP/301@192.168.0.6,20,tr) exten=>401,1,Dial(SIP/phone1,20,tr) 301 is the extension number for phone 2 in asterisk server

Still having trouble: >> cd /tmp >> ping -c 3 192.168.0.9 # check if TFTP server respons on ping >> tftp 192.168.0.9 # connect to TFTP server, you should get a new prompt OK to here using 192.168.1.9 for NIC eth(0) and tftpd server 192.168.1.9 New prompt is tftp> >> get aa This times out and returns to tftp> Unable to return to shell using exit

Hello, I am trying to flash new firmware into a router using TFTP-HPA. I am running Ubuntu 14.04 on a flash drive and still learning how to use Linux. I have also installed XINETD.D In one of the README files that comes with TFTP-HPA it said not to call it using tptp. Here are the instructions I'm trying to follow: cd /tmp ; tftp -gl aa 192.168.0.9; sh aa I do not know what

Hello, I've used tinc successfully for a long time, all with Linux hosts. No problem there. Unfortunately I now have to add a Windows host to the VPN. What a fight Winblows is! Probably just my ignorance. The VPN works and tinc says that tinc-up is run (and a debugging statement proves it) but I can't get an extra route added. tinc-up.bat contains: ------------------- netsh interface

Dear Asterisk-Users, does anyone know how to prevent non-free calls to Broadvoice Unlimited World ? This first thing I did is I accept only that coutry prefixes (in extensions.conf) that are in the Unlimited World dialplan. I was also able to filter out german cell phones (cause they begin with 1 and no landline is beginning with 1). US is also no problem as cell phone calls are unlimited

I'm still not getting my outbound to work. I've seen two patches relevant to broadvoice for chan_sip.c which apparently have already been added to CVS. I'm dropping all outgoing calls after ~30 secs. Asterisk doesn't seem to know they're gone though. I called my cell w/ broadvoice and turned on sip debug AFTer the call had physically dropped: *CLI> sip show registry

Hi, i'm having problems with broadvoice incoming calls. I can perfectly place calls but my Asterisk Box is having problems when registering with the SIP Proxy. Sometimes it register and the call gets into asterisk, but without sound (seems to be NAT problems) and sometimes its not possible for asterisk to receive the calls. Everything was working great exactly for a month, but a week ago it

Hi, in the Snom FAQ I found the following information: After staring up, the phone tries the URL given in the "Setting URL" of the phone. ... BTW this setting can also be set via DHCP. .... option tftp-server-name "http://192.168.0.9/snom200{mac}.htm" The documents used: FAQ-04-06-14-sf.pdf "Setting up DHCP for snom phones" FAQ-04-03-24-sf.pdf "How can I

I'm experiencing a "Failed to authenticate on INVITE" error (see output below) whenever I try to MAKE a call through the Broadvoice account. I noticed some others had the same problem but it went away when they rebuilt Asteris w/ a new version. N such luck for me! I'd be grateful for any assitance. Here's what I've done so far: 1) I downloaded the latest stable

Hi, I have two accounts with broadvoice. Now, I want to be able to distinguish between them. I though that this would be simple by adding "/EXTEN" at the end of the register statement. For example: register => num1:pass@sip.broadvoice.com/1000 Unfortunately, this is not working. When I call into my box I hear busy tone. My config looks like this: [root@voip asterisk]# cat sip.conf

In a 1.2 release of asterisk, I've had no problem connecting to a Broadvoice SIP peer, to allow routing outgoing calls from Asterisk to Broadvoice. Now, with the same SIP configuration, I cannot establish the peer. I've enclosed a SIP log in the hope that someone can help me analyze this failure. I'd guess the issue is NAT related and wondering if someone can spot a problem in the

Hello all, When I call the Broadvoice number all is good. When I try to call out through DISA on my broadvoice line i get the following: Executing Dial("SIP/147.135.0.129-0815bc60", "SIP/16037862111@proxy.bos.broadvoice.com|30") in new stack -- Called 16037862111@proxy.bos.broadvoice.com -- Got SIP response 480 "Temporarily Not Available" back from

I've tried everything with the * box after this weekend. I have read every document on the problems people are having with them after this weekend as well, but none of them address my problem. I checked my settings in my sips which I have below as well, I have changed the host file a few times, but this was new to me and I never had modified it before. I have and the same results

I have been going crazy with this also since Sat. Our server was working perfectly with BV but will now not place calls to BV. Incoming from BV works fine. I felt sad rebooting it today, it had been running for almost 200 days! Here is my error message from the console... Notice I am running today's CVS Connected to Asterisk CVS-03/08/05-14:32:39 currently running on com (pid = 1624)