similar to: Signaling on PRI channels

Hi all, I have to asterisk-1.0.9BRIstuffed-0.2.0n boxes each equipped with a TE410P. Box A is connected with pri1 to the PSTN. Box B is connected with pri1 (cpe) to the Box A at pri2 (net). Now I want Box B to dial out to the PSTN tunneled thru Box A and have it get all ISDN indications in case of call failure, eg. unallocated destination number etc. But currently Box B always gets only

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

Hello List I'm trying to figure out what is wrong between my asterisk and my NEC 2400 pbx We have been trying to link them with a spare PA-24DTG from the NEC, I'm able to call an extension on the Asterisk, however the extension rings, and then immediatly hangs up I traced it back to the debug of the PRI on the Asterisk... I would appreciate if anyone could pin point what is wrong The

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

I've a call center using IAX softphones provided by a third party. We've observed problems where the IAX phones seem unable to use our PRI trunks. A sample anonymized call is provided below with the PRI debug calls embedded. Any thoughts, comments or suggestions would be welcome. In anonymizing it, I preseved the format and number of digits sent. -- Accepting AUTHENTICATED

Dear Gurus, i am facing some unknown problem here.. first, let me describe my case. my office is using a nortel merridian option 11c PBX. and it is connected to the provider thru a E1 card, which is working fine with no problem. my plan it to slot in a server with 2 TE11XP card to intercept the outgoing calls. Provider <--te11xp---> asterisk <---te11xp------> nortel merridian

Salve, I'm somewhat stuck on how to get DTMF working with my setup and googling didn't yield anything similar. My setup consists of one CAPI-capable board (AVM Fritz!DSL) connected to a BRI (T-ISDN), one HFC-S board running in NT-mode connected to an internal S0 bus with some ISDN devices (DECT stations, TA) and, of course, some ethernet interfaces. ISDN standard used is Euro-ISDN.

handled. So....what do I do? Thanks, MD =1=================================================== !! Invalid Protocol Profile field 0x11 -- Accepting call from '2004000' to '111' on channel 0/23, span 1 -- Executing NoOp("Zap/23-1", "Incoming call from Meridian1") in new stack -- Executing NoOp("Zap/23-1", " From number: 2004000|

Hi all, I am using a Sangoma with two PRI's. As far as land phones, the calls are fine but it refuses all cellphone calls: My configuration in Zaptel is span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 span=2,0,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-61 and on Zapata.conf: [channels] language=it context=default switchtype=national

Hi all, I have some problem to send a FAX to a given number. I use asterisk 1.2.18, on a openSUSE 10.2, i586 host. The FAX is sent out via an ISDN PRI interface, I'm in Germany, and the destination FAX devices are in Germany too, but in different areas, so I have to use a city prefix. I did set the pri device in debug mode, below are two calls, to two different FAX numbers, the first is

picture. I know the firmware on the Nortel is old, so I'm guessing that libpri is sending something that the Nortel does not know how to handle. Is there a way to dumb down what libpri sends? From everything I've read PRI is an evolving standard - and older devices may struggle with newer extensions/developments. (This might be very handy for users trying to talk to old pbx's.) Is

Hey all. We have a DS3 circuit with GBLX split off into 7 systems with a 4 port sangoma card (A104D) in the first 2 systems, and digium T410P cards in the other 5. GBLX numbers their spans from 0 to 3 instead of 1-4 and we have a NFAS configuration with the d-channel on chan 96. All of our systems are running 1.0.7 for stability reasons (and no good time for maintaince, the entire platform

Hi Folks, I've Asterisk Bristuffed up and running behind an Auerswald Commander Basic ISDN PBX on the internal ISDN Bus (BRI/PTMP). The HFC Card works marvelleous for outgoing calls (as the parallely installed avm fritzcard with chan_capi does), but when I'm trying to call in, I get a short ring signal and then the connection is terminated. This does not happen with chan_capi and

Hello, Configuration: Asterisk CVS HEAD 20050730 on RH EL3+ DIGIUM TE110P PRI card + euroISDN E1 I am trying to sort out the problem: 1. Provider's switch sends "SETUP"; 2. Asterisk receives "SETUP", rings allocated extension but does not send "Setup acknowledge" (or any other messages) to switch; 3. After 4 seconds of waiting of *'s response switch sends

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

Hi, Ive been playing on a asterisk to orion gsm box E1 pri setup. I have achieved incoming calls to be passed to my asterisk box successfully but outgoing calls will just I have tried playing with various pridialplan and overlapdial settings and with no success. If anyone can make more sense from the log, I'd certainly appreciate it. I am sending a 10 digit number to be dialed. I guessed

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

hi all I have a PRI line which i have connected to my asterisk server. I am able to make calls to mobile no through my asterisk server, while i am not able to make calls to land line nos. This is strange. Where do u think the? problem is , is it from the service provider or? mis configuration of my asterisk. I am from India and using airtel pri lines. Below i am pasting you my configuration file

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

We are still having problems getting a Wildcard to work with a German E1 (PMX) interface. When starting asterisk it shows all B-channels starting up successfully (although our carrier told us only the first B-channel starts, if any at all). Incoming calls are not being signaled at all. (They seem to be intercepted by the carrier's switch, as no B-channel is up) Outgoing calls sometimes work,