similar to: X-Lite and * SIP Problem

Hi there, I have tried very hard to setup the x-lite with asterisk, but until now i didn't get sucess. When i start the asterisk in debug mode, i see the message: sip/2.0 401 unauthorized. I know that this problem with authentication. I put in my sip.conf as below. [2203] type=friend username=2203 auth=md5 secret=1234 reinvite=no canreinvite=no dissallow=all allow=gsm

I have just installed * from the latest CVS and I can make calls via X-Lite to outside numbers but for only 30 to 35 Seconds at a time then Broadvoice will hang up on me but X-Lite will not know it. Once I hang up X-Lite then I will get the following error message: Spawn extension (default, Number-I-Dialed, 1) exited non-zero on 'SIP/200-6a22' -- Got SIP response 404 "Not Found"

Gentlemen, Forgive me if I am posting at the wrong place! I was going to test the "new" chan_ooh323 driver so I did install: debian: Linux sip2 2.6.26-2-686 #1 SMP dahdi-linux-complete-2.2.0.2+2.2.0 Asterisk SVN-trunk-r231692 Did enable chan_ooh323, everything compiled without any problems. Hardware setup: Phone (975) - Avaya CM - H.323 - Asterisk - X-Lite (0317998975) X-Lite can

We are trying to use a softphone from a location that is behind a firewall. We are using x-lite as the softphone. So far, we've been able to get the phone to register with the asterisk server, and it can receive voice from the asterisk server (IE, voicemail, etc). However, asterisk can't hear anything from the softphone. We have used 2 different machines to test this on. We are watching

Hi, I am new here on this list, and have a problem of which I hope that somebody here can help me with it. I have a Voipbuster account, with which I would like to make phone calls via my Asterisk PBX. If I let X-Lite register directly at voipbuster.com, everything is OK, but if I let Asterisk register there, it says "registration for XXXXXX@sip.voipbuster.com timed out, trying again",

Hello: Here is my sip and extentions configuration and the log of x-lite, because i don`t can call inside my LAN with asterisk PBX 1.2 and i don`t have NAT. i hope you can help me. SIP.conf [default] include=>anexos include=>anexos1 include=>anexos2 [anexos] exten=> 100,1,Dial(SIP/100,0) exten=> 100,2,Hangup [anexos1] exten=> 101,1,Dial(SIP/101,0) exten=> 101,2,Hangup

Hi All, I am running asterisk on Linux machine and trying to use confbridge application. Please have a look at Conf files. sip.conf ====== [general] context=default allowoverlap=no bindport=5060 bindaddr=0.0.0.0 srvlookup=yes disallow = all allow=ulaw allow=alaw defaultexpiry=100 [5001] type=friend nat=yes host=dynamic canreinvite=no context= conferences disallow = all

Hi all, I'm working on an implementation of VoIP en Linux. I have a Debian Suse (*.*.*.173) with an * and a X-lite client and a Red Hat 9.0 (*.*.*.172) with another softphone X-lite. Both of the softphones are registering and appear in the peers (sip show peers) with the good parameters of address and port. If I try to make a call, * receive the INVITE request and send a 404 NOT FOUND answer.

Hi folks! I bought a X100P a while ago and know I've tried to get it working here at home again ... but I can't manage to get my X-Lite client working with Asterisk (CVS from a day ago) ... I've downloaded the latest version of X-Lite and I believe that I've set it up correctly ;-) But I cant get it to register with my Asterisk - I only get "Login timed out, contact your

Hi, I am trying to make external sip calls by using asterisk. Please provide information regarding sip trunk configuration in conf files. Setup is as below, * * *Case A:* Register two soft phones [X-lite] with 1000 and 10001 numbers to asterisk PBX [running in 192.168.1.11] and able to make calls in between. Sip.conf ====== [general] context=default bindport=5060

Hi all, Still having the one way sound problem. Any suggestions how to hunt the problem down ? Regards, Thorsten --------------------------------------------------------------- Hi all, We have a very basic * installation for testing purposes. The * is connected to PSTN with BRI and setup with X-Lite over plain lan. (local IP's) OS: Linux/Debian unstable. Asterisk CVS-10/29/03-23:46:26

Hello, Yesterday night we have upgraded our Asterisk from 1.2.32 to 1.4.24.1 with lipbri 1.4.10, dahdi-linux-2.2.0-rc4 and dahdi-tools-2.2.0-rc2. Libpri and dahdi is only for dahdi dummy cause of the meetme function. After the upgrade we had the problem that some Linksys spa941 phone at one location could not dial out. incoming calls to the phones works without any problem, but outbound the

Dear The Expert, I am very new with this, I have installed AsteriskNow, X-Lite as my SoftPhone, I am using SPA-3102. I have 3 extensions, me at 250, 998 is my Linksys SPA-3102 and 999 for PSTN Line (see below) My problem is, I am unable to call 998, I thought this is registration problem, (because the Linksys screen info said Registration Failed) Could any body please help? Many thanks in

Hi List, Additional with the latest tries from the below I get a nice random seg fault when I hangup on PSTN. (With obviously no sound on x-lite, still!) asterisk -vvvvgc results after hanging up the pstn line in: -- Executing Hangup("SIP/1087997-d79f", "") in new stack == Spawn extension (sip-phone-out, h, 2) exited non-zero on 'SIP/phonenumber-d79f' Segmentation

Hi all, We have a very basic * installation for testing purposes. The * is connected to PSTN with BRI and setup with X-Lite over plain lan. (local IP's) OS: Linux/Debian unstable. Asterisk CVS-10/29/03-23:46:26 chan_capi On the IP side: X-lite (build: 1084) Calling and get calls on PSTN from X-Lite is no problem. We only get sound from PSTN to X-lite. Never from X.-lite to PSTN. The

Greetings listers. I'm running asterisk 1.4.21.2 on SUSE 11.0 using Polycom 501 phones. My outgoing connections are Zapata using a TDM401P. For the most part I can make and receive calls fine except for these 3 issues: 1. When I call an external conference, the call never bridges and hangs up after 60-90 seconds. 2. When I call another number there is a

We have a machine with a TE410P in it acting as a client to route calls via iax2 to our central server, caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called client server often the called can't hear the caller (both machines on public ip) 'iax2 show netstats" on client machine shows more and more dropped packets on the

Hello All, I have a number of X-Lite users in countries where the incumbent Telco will do anything to block VOIP traffic. For some reason neither the X-Lite broadband or dialup clients would register with my server unless we configure them to use the Xten Xtunnels demo server. Once the Client has registered the call quality is great! The problem is the Xtunnels does not support other IP Hard

Hi All I am trying to dial out using SIP and Vonage using the instructions : <a href="http&#58;&#47;&#47;www.voip-info.org&#47;wiki&#47;view&#47;Asterisk&#43;and&#43;Vonage" target="_blank"

Preparing to use * for a 'real' installation shortly. Meanwhile, I've got a single port clone thing, 00:06.0 Communication controller: Motorola Wildcard X100P working to answer my landline and send calls to my laptop or voicemail. Sweet! Trying to "call out" from linphone, I set up this: exten => _X.,1,Dial(DAHDI/1,${EXTEN}) Both SIP client and this extension are in