similar to: Re: Polycom phones do not talk to each other

>Also, I'm sure you've probably checked on this one, >but are the phones registered with asterisk? >You can make outbound calls on them without them >actually being registered. I'm assuming you can >still get in and see the CLI. What does "sip show peers" >look like? What does "sip show peer xxx" show? >What does the CLI show when you

>> We have bought PBXware GUI from Bicom systems and configured >> extensions >> with Polycom Phones as UAs. >> >> The Polycom Phones can dial out and make calls but I cannot make >> extension to extension calling. >> >> Googling did not help much. >> >> As you may be aware PBXware is a closed source software GUI from Bicom >>

Sherwood, Your intentions are noble and your desire to build this, fullfills an immediate need for business. If your intention is just to build a GUI for Asterisk, read no further. If your desire is to build something more purposeful, your best bet would be to see the existing commercial GUI/HostedPBX offerings like Pbxware and Switchware from bicomsystems.com ( http://www.bicomsystems.com)

I have an issue where a particular dialplan works but another doesn't. I'm not sure why. To me they look identical and it has me stumped. This works: [to-test] exten => _X., 1, SetCallerPres(allowed) exten => _X., 2, Monitor(wav,/tmp/test-${UNIQUEID},mb) exten => _X., 3, Ringing exten => _X., 4, Dial(SIP/9330 at a-test,20,ro) exten => _X., 5,

Hi. I'm dialling two numbers - one that's unobtainable, one that's busy. ${DIALSTATUS} is coming back ANSWER each time right before the channels hang up. Am using the following dialplan macro to dial out. [macro-advdial] exten => s,1,Dial(${ARG1},20,g) ; Ring the interface, 20 seconds maximum exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status

Hi All, i want to configure voice mail on Asterisk 1.4 for multiple users. let me explain you the scenario. i have 10 users with the name of 1000,2000,3000,4000,5000,6000,.......and these user can call to each other. Now i want to configure separate voice mail box for separate user. my extensions.conf ..... settings below.. [voicemail] exten => _X.,1,Dial(SIP/${EXTEN}) exten =>

Hi, I'm trying to implement dynamic routing of incoming calls to local extension if previous outgoing call was unanswered. But after I do Goto to s-NOANSWER, variable ${EXTEN} changes to 's-NOANSWER'. I guess this is normal, but I don't understand why ? How to workaround on this one ? Thanks in advance, regards, Rob. [outbound-capi-ISDN] exten => _0.,1,NoOp(Calling ISDN

Hi All, I'd just like to verify what the correct operation of the timeout parameter is for the dial application. I'm not sure if I've encountered a bug or a configuration issue. When a sip phone is not responding to invites on an outbound call, the dial application still waits the duration of timeout before continuing with dialplan execution. I was under the impression that app_dial

I was wondering if it is possible (in 1.2.x) to get the SIP response code back after doing Dial(). Dial() seems to treat most call-setup problems as dialstatus CONGESTION, and some are NOANSWER, but I want to know the SIP response code, so I could return the right tones to the user, not just a congestion tone for every fault. Anyone know a way to find out that information, so I want the

Hi, I am facing some issues while using MixMonitor and StopMonitor. My extensions logic is attached below: exten => s,1,MixMonitor(${CALLERID(num)}_${TIMESTAMP}.gsm,b) exten => s,2,Dial(SIP/101,13) exten => s,3,StopMonitor() exten => s,4,NoOp(Dial Status: ${DIALSTATUS}) exten => s,5,Goto(sss-${DIALSTATUS},1) exten => sss-NOANSWER,1,VoiceMail(777 at salesvoice) exten =>

Hi all, I am from India and has been recently using asterisk for testing and enahncing my telephony knowledge. I am trying to use the originate Command from the Asterisk manager on both SIP and ZAP. The command works successfully but does not return any DIALSTATUS such as BUSY,ANSWER,NOANSWER as in case of command DIAL when used from the dial plan. Can some one guide me how to get the vaue of

Hi, BRIEF RESUME: Is there any other way to obtain the same result but being easier to configure?? Thanks! EXTENDED RESUME: i've configured a, rather difficult, macro that even for me without being documented is difficult. I ask for the help of the experts to know if the functionality it apports can be achieved better in another way. What i'm trying is to enable call a channel (e.g.

Hi all, I am trying to understand how I can get a simple IVR scenario to work properly (having already removed most of my hair...). The basic requirement is as follows: * Caller arrives at our main number * Caller is greeted and then told they can enter an extension number, if known, or wait and their call will be connected to an available rep. * The IVR then dials a group of extensions (if

Hello list, Hope all doing well! I've been checking some cases when a Dial fails and dialplan execution continues to handle this. I am finding it a little confusing how we should handle the DIALSTATUS and the HANGUPCAUSE in this situation.... More specifically, I am facing a case in version 13.6.0 where I am getting a DIALSTATUS=BUSY and HANGUPCAUSE=19 after receiving a 480 SIP error. Seems

Hi Guys, i spent some time to figure this out (since i love how dialplan is written) but i decided to ask for your help guys. i have two asterisk servers one is 1.2 the other is 1.4, from 1.4 (pbx1) to 1.2 (pbx2) i can leave a voice mail without any pb, but from pbx2 to pbx1 it just hang up. in pbx2 extensions.conf: i am using: exten => 8029,1,Dial(IAX2/pbx1/${EXTEN},20,tTWwr) in pbx1, i

I am using PBXware for configuring users and extensions. Pbxware uses Internal script called init.sh to process the calls based on its own version of extensions.conf defined in the GUI. I have IAX2 Extensions 56 and 101 and SIP extensions 50 and 51. I have used IAX2 extension 101 and dialed SIP Extension 51 But the PBXWare's Init.sh AGI command identifies the DNIS as another IAX

No Jeremy, excuse me, the error was in my email. The correct command is /bin/echo "Channel: Local/$1@chiamamezzi-dialout";\ /bin/echo "Variable: callid=123456|number=$1|url=pippo|menuid=FOP|redirectnum=0554202880";\ /bin/echo "Context: chiamamezzi-Wave";\ /bin/echo "Exten: s";\ /bin/echo "Priority: 1";\ /bin/echo "Callerid: Asterisk Automatic

Hi, I am looking at http://www.theschmandts.org/blog/?p=28 to setup missed call notification but i am having issue. following is my dialplan [macro-stdexten] exten => s,1,Dial(${ARG2}) exten => s,2,Goto(s-${DIALSTATUS},1) ; Jump based on status (NOANSWER,BUSY,CHANUNAVAIL,CONGESTION,ANSWER) exten => s-NOANSWER,1,Voicemail(${ARG1},u) ; If

Hello, We have a strange situation (asterisk 1.6.2.14), where we get a result for DIALSTATUS for BUSY and No-ANSWER, but nothing for CANCEL. This is the (relevant) test dialplan: -------------------------------- [incoming-private] exten => _X., n, Dial(SIP/1001,30) exten => _X., n, NoOp(${DIALSTATUS}) exten => _X., n, Gosub(incoming-status,s-${DIALSTATUS},1) [incoming-status] exten

I have a PRI line and I am having problems setting the ringtimeout on the dial application to more than 29. If I set ringtimeout to 29 on the dial application call and I do not answer the ringing phone then I correctly get DIALSTATUS set to NOANSWER. If I set ringtimeout to any value over 29 on the dial application call and I do not answer the ringing phone then I go to extension h and have